Serve one entity for period of time
This block serves one entity for a period of time, and then attempts to output the entity through the OUT port. If the OUT port is blocked, then the entity stays in this block until the port becomes unblocked. If an entity in this block is scheduled to time out, then it might depart prematurely via the optional TO port. For an example that uses the TO port of a queue block in the same way, see Use Timeouts to Limit Entity Queueing Time.
You specify the service time, which is the duration of service, via a parameter, attribute, or signal, depending on the Service time from parameter value. The block determines the service time for an entity upon its arrival. Service times are assumed to be specified in seconds.
Note: If you specify the service time via an event-based signal, be sure that its updates occur before the entity arrives. For common problems and troubleshooting tips, see Unexpected Use of Old Value of Signal.
The block permits preemption if you select Permit preemption based on attribute. In this case, an entity in the server can depart early via the P port. Preemption occurs only if attributes of the current entity and the entity attempting to arrive satisfy specified criteria. For details, see Preempt an Entity in a Server.
When the block does not permit preemption, the IN port is unavailable whenever this block stores an entity. In this case, the IN port becomes available when the entity departs.
Entity Input Ports
|IN||Port for arriving entities, which will be served.|
Signal Input Ports
|t||Service time, in seconds, for a newly arrived entity. This signal must be an event-based signal. You
see this port only if you set Service time from to |
Entity Output Ports
|OUT||Port for departing entities that have completed their service time, have not timed out while in this block, and have not been preempted.|
|P||Port for entities that have been preempted by an arriving entity. This port must not be blocked at the time of preemption.|
|TO||Port for entities that time out while in this block. You see this port only if you select Enable TO port for timed-out entities. This port must not be blocked when an entity attempts to depart here.|
Signal Output Ports
|Label||Description||Time of Update When Statistic Is On||Order of Update When Entity Departs|
|#d||Number of entities that have departed from this block via the OUT port since the start of the simulation.||After entity departure via the OUT port||4|
|#n||Number of entities currently in the block, either 0 or 1.||After entity arrival and after entity departure via the OUT or TO port||3|
|#p||Number of entities that have been preempted from this block since the start of the simulation.||After entity departure via the P port||4|
A value of 1 indicates that the block stores at least one entity that has tried and failed to depart. In that case, the entity is a pending entity.
A value of 0 indicates that the block does not store any pending entities.
Sample time hit of 1 occurs after the block stores an entity that has tried and failed to depart.
Sample time hit of 0 occurs after the departure of the pending entity via any port.
|w||Sample mean of the waiting times in this block for all entities that have departed from the OUT or TO port. An entity's waiting time might exceed its service time if the OUT port is blocked when the entity completes service.||After entity departure via the OUT or TO port||2|
|util||Utilization of the server, which is the fraction of simulation time spent storing an entity. At T=0, the utilization is 0 or 1 depending on whether the server contains an entity.||Performance considerations cause the block to suppress
signal updates until specific occurrences cause updates. In ||2|
|#to||Number of entities that have timed out from this block since the start of the simulation.||After entity departure via the TO port||4|
Output signals having the same number in the Order of Update column in the table above are updated in an arbitrary sequence relative to each other; you should not rely on a specific sequence for your simulation results.
The initial output value, which is in effect from the start of the simulation until the first update by the block, is 0 for all signals.
Determines whether the service time is computed from a parameter in this dialog box, an input signal, or an attribute of the entity being served.
The service time, in seconds, for all entities. You see this field only if you set Service
time from to
The name of the attribute whose value the block uses as the
service time for an entity. You see this field only if you set Service
time from to
The priority of the service completion event, relative to other simultaneous events in the simulation.
If you select this option, the block can replace an entity by a higher priority entity. Otherwise, the block never permits new arrivals when it is storing an entity. Selecting this option also clears the Average wait, w check box on the Statistics tab and makes that parameter unavailable.
The block uses this attribute to determine whether a new entity can preempt the one in the server. You see this field only if you select Permit preemption based on attribute.
Preemption occurs when the arriving entity has a strictly smaller
Ascending) or strictly larger (
value of the attribute named above, compared to the attribute value
of the entity in the server. You see this field only if you select Permit
preemption based on attribute.
If you select this option, a preemption event causes the block to set an attribute in the preempted entity. The attribute value is the remaining service time the entity would have required if it had not been preempted. You see this field only if you select Permit preemption based on attribute.
The name of the attribute the block uses when recording the residual service time of entities. You see this field only if you select Write residual service time to attribute.
Selecting this option enables the block to define a new attribute for the residual service time. Otherwise, the block issues an error if the attribute named above does not already exist. You see this field only if you select Write residual service time to attribute.
This option becomes relevant if an entity times out while in this block. Selecting this option provides a TO entity output port through which the timed-out entity departs. If you clear this option in a model that uses timeouts, see the If entity has no destination when timeout occurs parameter of the Schedule Timeout block.
These parameters determine whether certain ports produce data throughout the simulation, produce data only when you stop or pause the simulation, or are omitted from the block. For descriptions of the affected ports, see the preceding table, "Signal Output Ports".
Allows you to use the signal output port labeled #d.
Allows you to use the signal output port labeled #n.
Allows you to use the signal output port labeled #p. This field is available only if you select the Permit preemption based on attribute option on the Preemption tab.
Allows you to use the signal output port labeled pe.
Allows you to use the signal output port labeled w. This field is available only if you clear the Permit preemption based on attribute option on the Preemption tab.
Allows you to use the signal output port labeled util.
Allows you to use the signal output port labeled #to.
The server has idle periods that reduce its utilization. However, the server block recomputes the util signal only when the number of entities in the server changes. While the definition of utilization says that the utilization is less than 1 at time 3, the util signal remains at its previous value of 1 until the next entity arrives at time 4.
In a longer simulation, the differences in the value of util compared to its theoretical definition become less pronounced.