QSPI Peripheral Configuration

Map QSPI peripherals in the Infineon AURIX model to peripheral registers in the MCU

Since R2022b

expand all in page

Description

Add-On Required: This feature requires the Embedded Coder Support Package for Infineon AURIX TC4x Microcontrollers add-on.

View and edit the map of peripherals in the Infineon® AURIX™ model to the hardware peripherals.

Using the Peripheral Configuration tool, you can:

  • View and edit configuration parameters for QSPI peripheral block.

  • Configure the global parameters. To set the group peripheral, select peripheral in Browser > Peripherals > QSPI. For more, see Map Tasks and Peripherals Using Hardware Mapping.

  • Check for any conflicts between peripherals.

QSPI Peripheral Hardware Mapping

Open the QSPI Peripheral Configuration

  • In the Simulink toolstrip, go to Hardware tab and click Hardware Mapping.

    Hardware Mapping Tool

Examples

Parameters

expand all

Global parameters

Enables the QSPI transmit FIFO event.

When you select this option, the dialog box displays the Tx FIFO Mode Selection options.

Note

  • Enabling this parameter, expect that the data is handled through interrupts. Therefore it is mandatory to use QSPI block (Transfer mode as SPI Transmit) during the events.

  • Global parameters for enable Tx FIFO event and Rx FIFO event are not applicable if the QSPI block with Transfer mode is set to SPI transmit and receive.

Enables the QSPI receive FIFO empty event.

When you select this option, the dialog box displays the Rx FIFO Mode Selection options.

Note

  • Enabling this parameter, expect that the data is handled through interrupts. Therefore it is mandatory to use QSPI block (Transfer mode as SPI Receive) during the events.

  • Global parameters for enable Tx FIFO event and Rx FIFO event are not applicable if the QSPI block with Transfer mode is set to SPI transmit and receive.

Enables the QSPI error event.

Note

Enabling this parameter, expects that the data is handled through interrupts. Therefore it is recommended to use QSPI block (SPI receive or transmit as transfer mode) during the events.

This parameter is read-only.

This read-only parameter indicates the Tx FIFO events occur based on Batch mode-1.

Dependencies

To enable this parameter, select the Enable Tx FIFO event parameter.

Enables the QSPI transmit FIFO threshold limit.

Dependencies

To enable this parameter, select the Enable Tx FIFO event parameter.

This parameter is read-only.

This read-only parameter indicates the Rx FIFO events occur based on Batch move-1.

Dependencies

To enable this parameter, select the Enable Rx FIFO event parameter.

Select the type of trigger source for the QSPI.

Select the source of hardware trigger for the QSPI.

Dependencies

To enable this parameter, set the Trigger source parameter to Hardware trigger.

Enables the QSPI receive FIFO threshold limit.

Dependencies

To enable this parameter, select the Enable Rx FIFO event parameter.

Select the QSPI serial clock pin selection. The list varies based on the module selected.

Select the QSPI serial data out pin selection. The list varies based on the module selected.

Select the QSPI serial data input pin selection. The list varies based on the module selected.

Channel

Select the QSPI module 0 through 7 on the hardware board.

Select the QSPI transmit mode.

  • Continuous - This option activates the chip select signal till the data transfer completes.

  • Single-transfer - This option deactivates the chip select signal for every data element involved in the data transfer.

Specifies the rate of data communication between the peripherals connected (clock period).

Select the QSPI data heading in binary numbers.

  • MSB first - the bit furthest to the left (msb) is moved first from SDO pin followed by the subsequent left bits.

  • LSB first - the bit furthest to the right (lsb) is moved first from SDO pin followed by the subsequent right bits.

Select the QSPI clock polarity in idle state.

Select the QSPI clock phase.

Enables the QSPI clock parity.

When you select the Enable parity option, the dialog box displays the Parity option.

Select the QSPI clock parity.

Dependencies

To enable Parity parameter, select the Enable parity parameter.

Enable to configure the QSPI block to either transmit or receive data at a time. Disable to use for both transmit and receive at a time.

Dependencies

To enable this parameter, set the Transfer mode parameter to SPI Transmit in the QSPI block in the Simulink® model.

Select the QSPI chip select pin.

This parameter is read-only.

Select the QSPI channel 0 through 13. This read-only parameter indicates the channel corresponding to the CS pin selected.

This parameter is read-only.

This parameter is read-only. Select the QSPI chip select control.

Select the QSPI chip select active level.

Introduces the selected delay between the active edge of the CS pin and the first shift clock edge.

Introduces the selected delay between shift clock period of a data block and is followed either by the deactivating edge of CS pin, or a new data block in continuous mode.

Introduces the selected delay between the end of the last TRAIL phase of a frame.

Version History

Introduced in R2022b

See Also

| |