# Translational Hydro-Mechanical Converter

(To be removed) Interface between hydraulic and mechanical translational domains

**The Hydraulic library will be removed in a future release. Use the
Isothermal Liquid library instead. (since R2020a)**

**For more information on updating your models, see Upgrading Hydraulic Models to Use Isothermal Liquid Blocks.**

## Library

Hydraulic Elements

## Description

The Translational Hydro-Mechanical Converter block models an ideal transducer that converts hydraulic energy into mechanical energy, in the form of translational motion of the converter output member, and vice versa. The compressibility option makes the converter account for dynamic variations of the fluid density.

Using this block as a basic element, you can build a large variety of hydraulic cylinder models by adding application-specific effects, such as leakage, friction, hard stops, and so on.

The converter is simulated according to the following equations:

$$q=\frac{d\left(\frac{\rho}{{\rho}_{l}^{0}}V\right)}{dt}=\frac{d\left(\frac{\rho}{{\rho}_{l}^{0}}\right)}{dt}V+\frac{\rho}{{\rho}_{l}^{0}}\cdot \epsilon \cdot ({v}_{R}-{v}_{C})\cdot A$$

$$F=\epsilon \cdot p\cdot A$$

$$\rho =\{\begin{array}{ll}\frac{\left(\frac{\alpha}{1-\alpha}\right){\rho}_{g}^{0}+{\rho}_{l}^{0}}{\left(\frac{\alpha}{1-\alpha}\right){\left(\frac{{p}_{0}}{p+{p}_{0}}\right)}^{\frac{1}{\gamma}}+{e}^{-\frac{p}{{\beta}_{l}}}}\hfill & \text{ifcompressibilityison}\hfill \\ {\rho}_{l}^{0}\hfill & \text{ifcompressibilityisoff}\hfill \end{array}$$

where

q | Flow rate to the converter chamber |

A | Effective piston area |

v_{R} | Converter rod velocity |

v_{C} | Converter case velocity |

F | Force developed by the converter |

p | Gauge pressure of fluid in the converter chamber |

V | Piston volume |

α | Relative amount of trapped air |

ρ_{l}^{0} | Fluid density at atmospheric conditions |

ρ_{g}^{0} | Gas density at atmospheric conditions |

p_{0} | Atmospheric pressure |

γ | Specific heat ratio |

β_{l} | Bulk modulus at atmospheric conditions and no gas |

ε | Mechanical orientation of the converter (`1` if increase in
fluid pressure causes positive displacement of R relative to C,
`-1` if increase in fluid pressure causes negative displacement
of R relative to C) |

The piston volume is computed according to

$$\begin{array}{l}V={V}_{dead}+A\cdot \left({x}_{0}+x\right)\\ \frac{dx}{dt}=\epsilon \cdot \left({v}_{R}-{v}_{C}\right)\end{array}$$

where

V_{dead} | Chamber dead volume |

x_{0} | Piston initial position |

x | Piston displacement from initial position |

Port A is a hydraulic conserving port associated with the converter inlet. Ports R and C are translational mechanical conserving ports associated with the rod and the case of the converter, respectively.

The block dialog box does not have a **Source code** link. To view the
underlying component source, open the following files in the MATLAB^{®} editor:

For incompressible converter implementation —

`translational_converter_incompressible.ssc`

For compressible converter implementation —

`translational_converter_compressible.ssc`

## Basic Assumptions and Limitations

The block simulates an ideal converter, with an option to account for fluid compressibility. Other effects, such as hard stops, inertia, or leakage, are modeled outside of the converter.

## Parameters

**Piston area**Effective piston area. The default value is

`5e-4`

m^2.**Converter orientation**Specifies converter orientation with respect to the globally assigned positive direction. The converter can be installed in two different ways, depending upon whether it exerts force in the positive or in the negative direction when pressure is applied at its inlet:

`Pressure at A causes positive displacement of R relative to C`

— Increase in the fluid pressure results in a positive displacement of port**R**relative to port**C**. This is the default.`Pressure at A causes negative displacement of R relative to C`

— Increase in the fluid pressure results in a negative displacement of port**R**relative to port**C**.

**Compressibility**Specifies whether fluid density is taken as constant or varying with pressure. The default value is

`Off`

, in which case the block models an ideal transducer. If you select`On`

, the block dialog box displays additional parameters that let you model dynamic variations of the fluid density without adding any extra blocks.**Piston displacement**Select method to determine displacement of port

**R**relative to port**C**:`Calculate from velocity of port R relative to port C`

— Calculate displacement from relative port velocities, based on the block equations. This is the default method.`Provide input signal from Multibody joint`

— Enable the input physical signal port**p**to pass the displacement information from a Multibody joint. Use this method only when you connect the converter to a Multibody joint by using a Translational Multibody Interface block. For more information, see How to Pass Position Information.

This parameter is enabled when

**Compressibility**is`On`

.**Initial piston position**Initial offset of the piston from the cylinder cap. This parameter is enabled when

**Compressibility**is`On`

and**Piston displacement**is`Calculate from velocity of port R relative to port C`

. The default value is`0`

m.**Dead volume**Volume of fluid in the chamber at zero piston position. This parameter is enabled when

**Compressibility**is`On`

. The default value is`1e-4`

m^3.**Specific heat ratio**Gas-specific heat ratio. This parameter is enabled when

**Compressibility**is`On`

. The default value is`1.4`

.**Initial pressure**Initial pressure in the chamber. This parameter specifies the initial condition for use in computing the block's initial state at the beginning of a simulation run. It is enabled when

**Compressibility**is`On`

. The default value is`0`

.

## Ports

The block has the following ports:

`A`

Hydraulic conserving port associated with the converter inlet.

`R`

Mechanical translational conserving port associated with the rod of the converter.

`C`

Mechanical translational conserving port associated with the case of the converter.

`P`

Physical signal input port that passes the position information from a Simscape™ Multibody™ joint. Connect this port to the position sensing port

**p**of the joint. For more information, see Connecting Simscape Networks to Simscape Multibody Joints. To enable this port, set the**Interface displacement**parameter to`Provide input signal from Multibody joint`

.

## References

[1] Manring, N.D., *Hydraulic Control Systems*, John Wiley &
Sons, New York, 2005

[2] Meritt, H.E., *Hydraulic Control Systems*, John Wiley & Sons,
New York, 1967

## Extended Capabilities

## Version History

**Introduced in R2007a**