Community Profile

# Torsten Knodt

### A123 Systems GmbH

22 total contributions since 2012

Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation

#### Torsten Knodt's Badges

View details...

Contributions in
View by

Question

How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...

circa 2 mesi ago | 1 answer | 0

### 1

Question

How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...

circa 3 anni ago | 1 answer | 0

### 1

Solved

Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

oltre 3 anni ago

Solved

Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

oltre 3 anni ago

Solved

Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

oltre 3 anni ago

Automotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...

oltre 3 anni ago | 0

Solved

Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

oltre 3 anni ago

Solved

Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

oltre 3 anni ago

Solved

Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

oltre 3 anni ago

Solved

Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

oltre 3 anni ago

Solved

Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

oltre 3 anni ago

Solved

Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...

oltre 3 anni ago

Solved

Pizza!
Given a circular pizza with radius _z_ and thickness _a_, return the pizza's volume. [ _z_ is first input argument.] Non-scor...

oltre 3 anni ago

How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...

oltre 3 anni ago | 0

| accepted

Question

/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...

oltre 3 anni ago | 0 answers | 0

### 0

Question

What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...

oltre 3 anni ago | 0 answers | 0

### 0

How to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...

oltre 3 anni ago | 0

| accepted

Question

OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...

oltre 4 anni ago | 0 answers | 0

### 0

Question

Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...

circa 5 anni ago | 1 answer | 0

### 1

Question

Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...

circa 7 anni ago | 1 answer | 0

### 1

Question

Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...

oltre 7 anni ago | 1 answer | 2