Risposto
C2000 Code Generation slow to compile
Hi Matt, Any chance you could add your model for us to be able to reproduce the problem? You can contact tech support and se...

circa 7 anni fa | 2

| accettato

Risposto
Can simulink use TI C2000 LAUNCHXL-F28027F or F2808 to monitor a analog signal （200KHz）?
Hi Fuxin, You could use the <http://www.ti.com/tool/LAUNCHXL-F28377S F28377S LaunchPad> which has more memory and where you c...

circa 7 anni fa | 0

Risposto
Can simulink use TI C2000 LAUNCHXL-F28027F or F2808 to monitor a analog signal （200KHz）?
Hi Fuxin, We made drastic improvements to External mode in R2016b. You will not be able to reproduce the External mode result...

circa 7 anni fa | 0

Risposto
Can simulink use TI C2000 LAUNCHXL-F28027F or F2808 to monitor a analog signal （200KHz）?
Hi Fuxin, * First here are steps to get started with External mode: First make sure to have the latest version of the <htt...

circa 7 anni fa | 1

Risposto
c2000 embeded coder. f2978d simulink doubt
Hi Varun, The "protocol" mode is the culprit. It tries to establish communications using a proprietary protocol which is resp...

circa 7 anni fa | 0

| accettato

Risposto
How to increase acquisition frequency in real time? (TI Board F28379D)
Hi Jessé, In your <https://www.mathworks.com/matlabcentral/answers/349017-tms320f28379d-problem-with-external-mode?s_tid=answ...

oltre 7 anni fa | 1

| accettato

Risposto
TMS320F28379D: Problem with external mode
Hi Jessé Augusto, You should verify that your serial over USB is configured properly and that you are using the right COM por...

oltre 7 anni fa | 0

Risposto
Simulink TI C2000 Boot mode
Hi, This is a late reply for a question that is still relevant today. To be able to load code automatically from MALTAB/Simu...

oltre 7 anni fa | 1

| accettato

Risposto
Running Simulink models on a TI C2000 MCU
Try running the following command and make sure to go through the steps of setting up the compiler path. >> targetupdater ...

oltre 7 anni fa | 0

| accettato

Risposto
BOOSTXL-DRV8305 + LAUNCHXL-F28027F C2000 Piccolo LaunchPad
Hi Marcus, The DRV8301 booster pack is pin compatible with the DRV8305. The c28027pmsmfoc_ert.slx model made for the DRV83...

oltre 7 anni fa | 0

Risposto
Unable to run external simulation TI F28069M Matlab r2017a
Hi Jorrit, F28069M is fully supported by Simulink, you just need to pick the right linker command file in the configuration p...

oltre 7 anni fa | 0

| accettato

Risposto
Missing DAC Hardware Ressources for TI C2000 Delfino F28377S
Support for DAC on 283x7x devices is available as part of R2016b onwards. <https://www.mathworks.com/help/supportpkg/texasins...

oltre 7 anni fa | 0

Risposto
TMS320F28027: Simulink SCI transmit disable
You can use an "Enabled Subsystem" and put your SCI Transmit block inside to only send when you want. The control of the enabled...

oltre 7 anni fa | 0

| accettato

Risposto
Output Format of ADC Block in Embedded Coder for C2000 MCU
[0 4095] I hope it helps!

oltre 7 anni fa | 0

Risposto
Communication Issue with Spectrum Digital C2000 XDS510LC JTAG
Hi Puneeth, By default, our models using the F2812 controller are configured to use a Blackhawk JTAG emulator. Here is how y...

oltre 7 anni fa | 0

| accettato

Risposto
How can I get the code execution tome of the model in simulink? (for the code generation of the C2000 processors)
Hi JIANWEI, Here are 2 techniques that will help you profile the execution time of the generated code on the TI C2000 process...

oltre 7 anni fa | 1

| accettato

Risposto
C2000 Support Package - Can't get CLA code to inline parameters
Hi Chris, In the <https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/examples/using-the-control-law-accelerator-...

oltre 7 anni fa | 0

Risposto
Building and debugging C code generated using Embedded Cider in CCSv5.5?
Hi Mayank, In R2017a, we introduced the "Open CCS Project" link that appears at the bottom of the diagnostic viewer, after yo...

oltre 7 anni fa | 0

Risposto
F28335 100kHz ePWM control with ADC interrupt
Hi Eneko, You are in control of the ADC conversion time. On the configuration parameters of your model, in the ADC parameters...

oltre 7 anni fa | 1

Risposto
LAUNCHXL-F28379D: MATLAB Simulink external mode error
Hi mmax177, We introduced fast External Mode in R2016b which provides better serial streaming capabilities while running Exte...

oltre 7 anni fa | 0

Risposto
C2000 Support Package - Can't get CLA code to inline parameters
Hi Chris, Sorry that you had to go through this pain. We are working on better integration of the CLA in Simulink, unfortuna...

oltre 7 anni fa | 0

Risposto
C2000 Embedded coder -- Change default time-out
Hi Mike, Usually the External mode time out is more then enough and the fact that you hit it probably means that you have a c...

oltre 7 anni fa | 0

| accettato

Risposto
'c2000hostsci_rx.tlc' file for the MATLAB S-function 'c2000hostsci_rx' in block host SCI RCV doesn't exist
Hi Reina, You are trying to use serial HOST blocks. These are meant to work only on your host computer in simulation mode tra...

oltre 7 anni fa | 0

Risposto
F28335 100kHz ePWM control with ADC interrupt
Hi Eneko, 1) On the F28335, flash is much slower than RAM. You want the code running at 100kHz to execute from RAM, I explain...

oltre 7 anni fa | 1

Risposto
Real time debug CCSv5 and MATLAB
Hi Caleb, The parameter tuning part of External mode does exactly what you are looking for. You can even use the dashboard...

quasi 8 anni fa | 0

Risposto
Matlab R2013a Simulink & CCS 6.1.0 - F28069
Hi Luca, No more Target Preferences block in 13a. You will find the target settings in the configuration parameters, once you h...

quasi 9 anni fa | 0

Risposto
Real Time Parameter Tuning in the target F28335(Experimenter Kit) using Matlab Simulink 2013b and CCS version 5.
Hi Sam, Starting in MATLAB release R2015a, External mode is supported via a serial connection with the target. You can use the ...

quasi 9 anni fa | 1

Risposto
Interfacing C2000 ADC and SCI Tx
Hi Nityanand, While running out of flash, the ramfuncs section needs to be copied from Flash to RAM at startup. This is what...

oltre 9 anni fa | 0

| accettato

Risposto
Matlab 2011b and ccsv4
Hi Cris, Very strange... Do you confirm you are using MATLAB R2011b? The command works on my side, if I try to enter some b...

oltre 9 anni fa | 0

Risposto
how to interface ccsV5.3 with Matlab 2012 or Matlab2013 useing dsp tms320f28335 processor and os is windows 8.1
Hi Rajul, I would encourage you to watch the following video: <https://www.youtube.com/watch?v=AY4GzMLl30A Simulink code g...

oltre 9 anni fa | 0