J Chen
Followers: 0 Following: 0
Statistiche
RANK
417
of 289.875
REPUTAZIONE
179
CONTRIBUTI
10 Domande
155 Risposte
ACCETTAZIONE DELLE RISPOSTE
30.0%
VOTI RICEVUTI
22
RANK
6.123 of 19.604
REPUTAZIONE
181
VALUTAZIONE MEDIA
5.00
CONTRIBUTI
5 File
DOWNLOAD
26
ALL TIME DOWNLOAD
1655
RANK
of 144.253
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Are Simscape's Principal Axes in a particular order from least to greatest moment of inertia?
The axes of the Inertia Sensor are the same as the axes of the frame that the sensor is attached to.
4 mesi fa | 0
The issue encountered during the simulation of the Stewart platform: "The motion is singular."
Make sure the mechanism is not over-constrained. Add inertia between two connected joints.
4 mesi fa | 0
simscape electrical long-term simulation
Yes. You can adjust the solver parameters in the Simulink Model Settings.
4 mesi fa | 0
Simscape PS converter error
The filter in the PS converter is not used to filter the command in conentional sense. The filter is used to make a system solva...
5 mesi fa | 0
Rigid Transform input data sequence
Use a rotation joint (such as the gimbal joint) and connect it to a solid. Specify motion indtead of torque as actuation. Here i...
5 mesi fa | 0
How to observe the acceleration profile of a pneumatic (cylinder) system?
Mechanical sensors can be used to measure acceleration - Link.
5 mesi fa | 1
Using a Simulink dynamic motorcycle in a driving scenario trajectory.
You need to use a lateral controller such as Pure Pursuit (in the Navigation or Robotics toolbox) or Stanley (in the Automatic D...
8 mesi fa | 0
| accettato
How to access the eigenvalues and eigenvectors of a M-DOF system built in Simscape?
You can linearize the Simscape model.
8 mesi fa | 0
Building a nonlinear spring in Multibody
You can use the Trnasform Sensor block to sense motion, convert the output to Simulink signals, calculate corresponding forces u...
10 mesi fa | 0
Failed to load library 'RP_Simulator_Components' referenced by
You can download the library from https://www.mathworks.com/matlabcentral/fileexchange/67157-robotics-playground
10 mesi fa | 0
My "generic engine" block seems to not care about the throttle input.
The attached file contaons a running example. These are my suggestions: It seems that some inertia need to be associated with t...
10 mesi fa | 0
Free Fallen object simulation
You can use the Block Solid in the Body Elements. Also use the Transform Sensor in the Frames and Transforms to measure the tran...
11 mesi fa | 0
About adding motion directly to the end-effector
Connect a 6 DoF joint to the end effector and ground. Specify the displacements of the 6 DoF joint. Rember to set the Filtering ...
circa un anno fa | 0
Number of variables vs number of equations in Simscape components
For a Simscape component, the variables include variables in the variables AND nodes sections as in this example. The number of ...
circa un anno fa | 0
No simscape simulation log
Open Model Settings (ctrl-E). Select Data Import/Export. Uncheck Single simulation output.
circa un anno fa | 0
Programmatically connect SimScape blocks
set_param('mymodel/Res2','position',[220,120,180,160]) is wrong. The third number (180) needs to be greater than the first numb...
circa un anno fa | 0
simulink-ps converter output with on signal
You should see the signal at both scopes. Make sure the axis scalings are appropriate.
circa un anno fa | 0
Need to assemble a submarine in simscape multibody make it move according to the precalculated trajectory. 1) All details of submarine are separated 2) How to make it move?
All components are rigidly connected in the model. You need to remove a solid line and add a joint between two components to mak...
circa un anno fa | 0
| accettato
How to use the DATA Inspector with SimScape model
You need to use Sensors and Transducers block to measure the variables, then convert the Simscape signals to the Simulink signal...
circa un anno fa | 0
Is it possible to open matlab function block editor code in the standard script editor?
One option is to right click at the block and choose Open in New Window.
circa un anno fa | 0
Communicating Simscape multibody with temperature and pressure sensors
Simscape Multibody doesn't deal with heat and temperature. You need to build a thermal model either with the Thermal Library in ...
oltre un anno fa | 0
| accettato
how to attach custom frame to cylindrical solid
You can use the Rigid Transform block as an alternative.
oltre un anno fa | 0
Extract Spring data from the revolut joint
Expand the Sensing fiels and check the position. A port will appear to output the position. Use a PS-Siumulink Converter block i...
oltre un anno fa | 0
ssc_mass_spring_damper_control example, all forces become 0 when no feedback?
The mass is stationary and the spring and damper generate no force at time zero. No force is applied to the mass if the PID is r...
oltre un anno fa | 0
Is there any two wheeler drive cycle file in MATLAB or simulink?
You can download the speed profile in Excel at (https://cleanfuturemobility.com/driving-cycles/) and import it into Matlab/Simul...
oltre un anno fa | 0
| accettato
SIMSCAPE MULTIBODY: Apply Forces / Sense velocity of GLOBAL Center of Mass
First add a new frame to the Center of Gravity (CoG). Connect a 6 DoF Joint between the new frame to the World Frame. Specify ...
oltre un anno fa | 0
How to get the coordinates of points in the simulink multibody model?
You can add a Transform Sensor to your system.
oltre un anno fa | 0
How to loop a model's output back to the input untill they both converge
Use a Delay block https://www.mathworks.com/help/simulink/slref/delay.html
oltre un anno fa | 0
| accettato
(Simscape multibody) Is there any way to use a specific angle as a input for revolute joint?
Set the Actuation tab as follows: Torque - Automatically computed, Motion - Provided by Input. You also need Simulink-PS Convert...
oltre un anno fa | 0
Generic Engine stalling when load applied
You need to specify an initial speed for the propeller. It is done in the Variables tab of the Propeller Inertia block.
oltre un anno fa | 0