Risposto
How to solve the "No rule to make target `.refresh', needed by `ert_main.o.opt'. Stop." when I use Embeded Coder to build generated C code?
Hi, The error "No rule to make target" is typically thrown by the make/gmake build automation tool because it can't find the in...

circa un anno fa | 0

Risposto
TMS320F28377D Simulink External Mode Error
Hi, I understand you are encountering an “rtiostream timeout” error. One possible cause for this issue could be that the GPIO ...

circa un anno fa | 0

Risposto
Failed to generate binary inputs.
Hi Manas , I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particular error ...

circa un anno fa | 0

Risposto
Failed to generate all binary outputs.
Hi Tarek, I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particular error m...

circa un anno fa | 0

Risposto
How to resolve "Failed to generate all binary outputs" while deploying code on F28335 Microcontroller using Simulink
Hi Muhammad Azeem, I understand you are encountering a “Failed to generate all binary outputs” error in MATLAB. This particula...

circa un anno fa | 0

Risposto
Run Time Error in Texas Instruments C2000 PIL Testing
Hi Sivakumar, I understand you are encountering an “rtiostream timeout” error when trying to run a PIL simulation on a C2000 ta...

circa un anno fa | 0

Risposto
How to use Matlab generated PWM pulse in C2000 epwm block
Hi Pratyay, I understand you want to use a MATLAB-generated PWM pulse in the C2000 ePWM block. You can use the MATLAB-generat...

circa un anno fa | 0

Risposto
Linearize FMU model in Simulink
Hi Alberto, I understand you want to understand if import bock supports linearization of FMU models. FMU import block supports...

circa un anno fa | 0

Risposto
TI C2000 Microcontroller Slow IPC-Transmission of an int32 with just 1kHz
Hi Marcel, I understand you are experiencing performance issues with the IPC transmission. When testing the IPC connection in c...

oltre un anno fa | 0

Risposto
Stoping epwm after one period via one-shot trip
Hi, I understand you want to disable the ePWM after a trip event. The Trip Zone settings of the ePWM block can be configured to...

oltre un anno fa | 0

Risposto
How to send these ADC values in a buffer over SPI using c2000 blocks
Hi Haadia, I understand that you want to share the ADC data to SPI. You can use the SPI Transmit (or Receive) block to send (o...

oltre un anno fa | 0

Risposto
TMS320F28335: how to disable epwm module after a certain time in simulink
Hi, I understand you want to disable the ePWM module. You can use the Trip Zone unit to disable the ePWM. You may select the s...

oltre un anno fa | 0

Risposto
Why does the spi block not send the second value?
Hi Haadia, I can understand that you are not able to send complete data through the SPI blocks. Following the steps mentioned b...

oltre un anno fa | 0

Risposto
when I use TI C2000 microcontroller blockset demos to generate code for F28069 Launchpad, error reports like these
Hi Bin, I understand you are encountering the error: 'The left-hand side of a . operator must be a valid scope identifier' when...

oltre un anno fa | 0

Risposto
cast shadow in Simulink 3D Animation
Hi Simon, I understand you want to cast the shadow of an object onto another surface in Simulink 3D Animation. To achieve this,...

oltre un anno fa | 0

Risposto
Error when using MATLAB toolbox for Ryze Tello Drones: Dot indexing is not supported for variables of this type.
Hi kiattisak, I can understand that you are getting the following error: “Dot indexing is not supported for variables of this ...

oltre un anno fa | 0

Risposto
Abnormal exit error while running model advisor check
Hi Niraj, I understand you are receiving an unexpected error when running model advisor on your Stateflow model. This appears t...

oltre un anno fa | 0

Risposto
Incapable of getting datas from Arduino Mega 2560
Hi Pierre-Olivier, I can understand that you are getting the following error: External Mode Open Protocol Connect command fail...

oltre un anno fa | 0

Risposto
Finding the transfer function of a DC-DC Converter and then calculating PI values for controller
Hi Chukwudalu, To understand the Dual Active Bridge converter, you shall refer to the following demo on “Modeling and Control o...

oltre un anno fa | 0

Risposto
How to get loan value for fixed time span and payment
Hi Peter, I understand that you want to calculate the remaining loan amount using a built-in function. You mentioned the 'amort...

oltre un anno fa | 0

Risposto
How does Model Advisor determine the default configuration ?
Hi Mohamed-Marwan, I understand that you want to run a particular set of checks every time on a model and wish to know how the ...

oltre un anno fa | 0

Risposto
Detect if block is part of a feedback loop
Hi Vince, I understand that it can sometimes be confusing to follow the flow of a model, especially when dealing with large and...

oltre un anno fa | 0

Risposto
some letters like "c""d" can't display correctly in commandline
Hi, I understand that when the lowercase letters c, d, and o are pressed, they appear as blanks. This issue appears to occur ...

oltre un anno fa | 4

| accettato

Risposto
How can I constrain a plot on an excel sheet?
Hi Christian, To ensure your chart remains within a specified area on the Excel worksheet, you can define its position and dime...

quasi 2 anni fa | 0

Risposto
How do I make a contour?
Hi 민제 강, To achieve smoother contours in your plot, you can interpolate the kerr onto a finer grid using interp2. Create a dens...

quasi 2 anni fa | 0

Risposto
Replacement for MFE Toolbox Function normloglik
Hi Tilman, In MATLAB, if you are using the MFE Toolbox and encounter an issue with the function normloglik not being recognized...

quasi 2 anni fa | 0

Risposto
How to do probabilistic forecast in Matlab?
Hi israt, In MATLAB, there are several options for performing probabilistic forecasting, particularly in the context of energy ...

quasi 2 anni fa | 0

Risposto
How can i do Probabilistic time series forecasting?
Hi israt, In MATLAB, probabilistic forecasting can be approached using two primary functions: 'forecast' and 'simulate'. The 'f...

quasi 2 anni fa | 0

Risposto
How to specify a seasonal ARIMA model
Hi Md. Golam, To specify a seasonal ARIMA model with the given parameters you can use the 'arima' function as follows: % Defin...

quasi 2 anni fa | 0

Risposto
How to specify a Seasonal ARIMA model?
Hi Dinuka, To specify a seasonal ARIMA model with the given parameters in MATLAB (R2023a), you can use the 'arima' function as ...

quasi 2 anni fa | 2