Risposto
Solving equations in a for loop with changing variables
Hi Samantha The first line in your code in the loop is not correct. It should d(i)=d(i-1)-S.*x(i). But then the loop must start...

oltre 3 anni fa | 0

Risposto
2P-MA Heat Exchanger Block Not Stable
Hello Tech When looking at your diagram, i believe that the model is over-constrained on both 2p and MA end sides. You sho...

oltre 3 anni fa | 0

| accettato

Risposto
Simscape - Allow accumulator to fully discharge without model crashing?
Hi Nicholas I think you should have a higher pressure in the tank. That will prevent the motor to overspin and thus avoiding ...

oltre 3 anni fa | 0

Risposto
Why is my Simscape gas fan simulation so incredibly sensitive to temperature and flow resistance?
Hello Colin, I think that Starting from Steady State can be a difficult choice to start with. I would recommend that you ...

oltre 3 anni fa | 0

Risposto
How can I simulate no-load saturation of a synchronous machine?
Hi Matthias I would give this a go with a recent release of Simscape Electrical where we have added load flow analysis and sy...

oltre 3 anni fa | 0

Risposto
Transmit rotational motion of a swinging door to a shaft rotation in Simscape multibody?
Hello Joben Indeed. It is best to assemble the pieces in Simscape Multibody procent n this case. The common gear constraint i...

oltre 3 anni fa | 0

Risposto
Calculation of an Variable in Custom Simscape Component seems to be wrong
Hello Moritz It looks like Simscape might initialize the variables Te and Te_out with a given value that then leads a differe...

oltre 3 anni fa | 0

Risposto
Simulation of air with oil mist / fog in simscape
Hello Andreas This might be possible to accomplish but requires a thorough qualification to capture your requirements. It...

oltre 3 anni fa | 1

Risposto
Why the Ideal Angular Velocity source is used in the Calculate Performance Curves of BLDC simulink model?
Hello there, The speed is constrained on the motor shaft. Then, a trapezoidal modulation determines the amount of electric po...

oltre 3 anni fa | 0

Risposto
Simscape Multibody close to real time animation of model "ball on plate", solver and contact library question
Hello David, I believe you took the right steps in your previous test. Keep in mind that in recent releases of Multibody (20a...

oltre 3 anni fa | 0

| accettato

Risposto
Problem with simscape Heat Exchanger (TL) component
Hello Rohan I think that the hot side is modelled as fluid flowing from a reservoir, through the exchanger and then ending in...

oltre 3 anni fa | 0

| accettato

Risposto
Simscape Multibody: Variable Stiffness in Revolute joint with motion as input
Hi Raphael There is no simple way of doing this by remaining in kinematic mode (constrained motion). If you use the joint...

oltre 3 anni fa | 0

Risposto
Simulink Fuel Cell Stack - Partial Pressures
Hi Matthew My interpretation is that high utilization of H2 and O2 leads to these residual pressures pH2 and pO2 being very l...

oltre 3 anni fa | 0

Risposto
Modeling Half-Car Suspension in Simulink/Simscape?
Hello Agustin I think that you’ll find inspiration in the Lever block in the Simscape Foundation Library, possibly by complem...

oltre 3 anni fa | 0

Risposto
Electrolyser for hydrogen production model
Hello Felix It is possible to do by using Simscape language and implementing the equations. But what is available now and in ...

oltre 3 anni fa | 0

Risposto
How to download previous versions of simscape and simmechanics?How to download previous versions of simscape and simmechanics?
Hi Aldo If you have an active license for these products, you should be able to log in to your MathWorks account and then downl...

oltre 3 anni fa | 0

Risposto
Simscape run-time parameter in code generation
Hi Ramkumar It should be visible in the Interface parameter in the generated code. Publish the report and the parameter shall...

oltre 3 anni fa | 0

| accettato