Risposto
How could I control the thermal coupling between two elements (e.g. two battery cell)?
Dear Mustafa, Thank you for your question. Simscape Electrical has a battery cell block which has the option of turning on the...

oltre 6 anni fa | 0

Risposto
How can I speed up my simualtion?
Hello Raphael, Thank you for sharing this. There are several ways in which you could speed up your simulation. They include: R...

oltre 6 anni fa | 0

Risposto
Change the capacity of the battery using Generate Parameter Data for Equivalent Circuit Battery Block
Dear Sumukh, The capacity in that block is Battery capacity table. On line 200 of the script Example_DischargePulseEstimation.m...

oltre 6 anni fa | 0

Risposto
How do I simulate battery performance in the next 5 years, using existing 5 years trend?
Dear L. Sugu, Thank you for your inquiry. If you have capacity fade and internal resistance increase as part of your last 5 ye...

oltre 6 anni fa | 0

Risposto
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hi, Md., You can still use SPS in that case. The main difference with SimElectronics is that the latter models all nonlineari...

circa 11 anni fa | 0

Risposto
¿Why the battery (electrical source component in SimPowerSystem Matlab/Simulink toolbox) discharge at the same rate with different capacities?
Hello, Jorge, I am attaching a model like you describe above and it seems to work correctly for me. Please make sure you cli...

circa 11 anni fa | 0

| accettato

Risposto
Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid
Hello, Md., If the AC part of your system is three-phase and you can neglect thermal effects on the semiconductor devices and...

circa 11 anni fa | 0

Risposto
How can I generate the setup of AC sweep for AC Voltage source in either Matlab or simulink?
Hello, Robert, I believe the Chirp Signal may do the job for you. It is in the Sources section of the Simulink library. Be...

oltre 11 anni fa | 0

| accettato

Risposto
Problems with model behaviour, hanging-up in a loop.
Hello, Joel, Would you please attach the model to this thread so I can take a look and try to better understand the issue? ...

oltre 11 anni fa | 0

| accettato

Risposto
How to model a solar powered electric grid in Simulink?
Hello, Faraz, I suggest you consider the use of SimPowerSystems for your design. You can find some examples here: http://w...

oltre 11 anni fa | 1

| accettato

Risposto
Simscape thermal mass discrete model
Dear Lalumet, A discrete solver can be used if you set up "Use Local Solver" in the Simscape Solver configuration block. Ple...

oltre 11 anni fa | 0

Risposto
How to make a Variable resistor in Sim powersystem not Simscape.
Hello, Adroit, You can combine a current meter and a controlled voltage source to create a variable resistor. Please see att...

oltre 11 anni fa | 2

| accettato

Risposto
Battery Model Simulink for 12V
Hi, Samad, Please open the battery cell block and comment out the SOC, DOC, and T blocks. This will prevent the second error ...

oltre 11 anni fa | 1

| accettato

Risposto
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Yes, that is possible. There are a couple of options: 1) Use SimPowerSystems Simscape Components. The blocks...

oltre 11 anni fa | 0

| accettato

Risposto
lead acid battery simulink
Hello, Simon, You may want to check this submission for an example of what you are trying to model: http://www.mathworks.c...

oltre 11 anni fa | 0

Risposto
Battery Model Simulink for 12V
Hi, Samad, The series connection in Simscape is realized connecting the + terminal of each cell to the - terminal if the adja...

oltre 11 anni fa | 0

Risposto
Bringing battery simulation results (parameter estimation) to hardware
Hello, Valentin, Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond des...

oltre 11 anni fa | 0

| accettato

Risposto
How to connect generic battery to an electrical circuit which is created using Simscape??
Hello, Mirza, Can you please attach a screenshot of your model so that I can take a look? Your problem is typically related ...

oltre 11 anni fa | 0

Risposto
Error with Simscape simulating
Hello, Nikolaos, Your model is missing an electrical reference (ground). Please add one and let me know if you still get an e...

oltre 11 anni fa | 5

Risposto
Recharge battery by induction on simulink
Hello, Titouan, Please try inserting an electrical reference block on the right hand side of your magnetic circuit. It needs ...

oltre 11 anni fa | 0

| accettato