Domanda
how to open figure one simulink
how make bock of m-file which contain figure and open it on simulink remark: simulink is on line (time inf)
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
figure
how to move line in a figure continuously by which one of its ends fixed at zero and the ling move around zero
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
signal processing managment
if i have signal how can i obtain its peak frequency in array if my time is inf
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
communication system
in fm-cw radar i use saw tooth ans sweep of freq when i sweep frequency the reflected signal with the same frequency but shifted...
oltre 12 anni fa | 1 risposta | 0
1
rispostaInviato
Developed FM-CW Radar approach
this project correct the error which occur in the previous project
oltre 12 anni fa | 3 download |
Domanda
figure
if i plot point(x) in a graph how can i remove it from graph
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
I/O interface
what are the I/O ports available which i can use it to make real time system e.g: analog signal needed to be processed by matl...
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
simulink
if i have a simulink model and the output of low pass filter is sin signal with certain frequency if i want to know this frequen...
oltre 12 anni fa | 2 risposte | 0
2
risposte
Domanda
signal processing frequency estimation
if i have a simulink model and the output of low pass filter is sin signal with certain frequency if i want to know this frequen...
oltre 12 anni fa | 0 risposte | 0
0
risposteRadar System
okey, chirp signal can be generated from vco block in comm.block set drived by saw tooth from signal genrator in source block ...
oltre 12 anni fa | 0
Domanda
gui
hello, i need any information bout gui because i ammaking radar system with scope
oltre 12 anni fa | 2 risposte | 0
2
risposteDomanda
can this program improved
hello, i make frequency modulated continouse wave radar using simulink <http://www.mediafire.com/?10kw7vsdfpo7rrs>
oltre 12 anni fa | 0 risposte | 0
0
risposteHow to continously run and display the simulink results ?
you can adjust simulation time to inf then use your scope you can watch your signal
oltre 12 anni fa | 2
| accettato
Domanda
frequency estimation
i make fmcw radar and the output of mixer will be connected to the mic socket in my labtop then i use simulink to calculate rang...
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
simulink &m-file
i have m-file code and a simulink model can i convert m-file code to block in simulink which i can make its input port a sinus...
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
data analysis
if i have array x and i want to get the index of maximum value of it ex:x=[1 2 3 4 5 0 11] i want command which give me that ...
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
simulik
need block its input a signal and its output is frequency of signal
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
simulinke with m-file
can i make interface between a simulink file and m- file ? simulink the op signal is sin and i need m-file to calculate frequen...
oltre 12 anni fa | 1 risposta | 0
1
risposta0
risposteDomanda
simulink
if i have a signal in simulink and i want to calculat frequency what can i do?
oltre 12 anni fa | 1 risposta | 0
1
rispostaDomanda
system failure
i used simulink : i used audio device to acquiring data from mic then make some processing and drive it by speaker after that m...
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
data transfer
i take data from audio micin simulink and i want to make some processing for data in m file
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
labview data connection
hello,how to transfer data from simulink to labview and if it can not be done i want to make radar scope on simulink
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
simulink rf receiver
can i make rf radio operate at 1 mhz in simulink when antenna is connected to microphone audio device
oltre 12 anni fa | 0 risposte | 0
0
risposteGUI BUTTON
you can make this operation by visual basic then use data interface to complete your design on matlab
oltre 12 anni fa | 0
Domanda
real time
can simulink deal with audio signal which have frequency 10khz? and why simulink doesn't run normally in high freqeuncy ? i.e ...
oltre 12 anni fa | 0 risposte | 0
0
risposteDomanda
fm-cw radar
this is the code of rx of fm-cw radar to get beat frequency is this correct? %receiver of fm-cw radar clear all;clc;cl...
quasi 13 anni fa | 0 risposte | 0