Community Profile

photo

Mahmoud Saleh


City Collage of New York

Last seen: oltre 3 anni fa Attivo dal 2015

My research involves microgrid control and design, microgrids clustering, intermittency of renewable-based MG, and integration of microgrids to electric power grids. Also, I investigate the feasibility of smart grid implementations. Moreover, I am involved in writing technical proposals.
Please contact me for collaboration and discussing my recent work regarding electric energy markets, cyber-attacks, and machine learning application in power systems.
https://www.linkedin.com/in/mahmoud-saleh/

Statistiche

All
  • Personal Best Downloads Level 4
  • First Review
  • 5-Star Galaxy Level 5
  • First Submission
  • Revival Level 3
  • Knowledgeable Level 1
  • First Answer

Visualizza badge

Content Feed

Visto da

Inviato


Applications of Complex Network Analysis in Electric Power Systems Code
Code used in the paper: Applications of Complex Network Analysis in Electric Power Systems

oltre 5 anni fa | 6 download |

Thumbnail

Risposto
Simple DC/DC Converter
I would say take a look at the following models, you should find the detailed modelling steps: https://www.mathworks.com/matlab...

circa 6 anni fa | 1

Risposto
i konw to make bidirectional dc to dc converter.but it does not give the perfect answer.please check and give me the solution.i have attached my design
Please check those two models for detailed modelling of bidirectional converter: https://www.mathworks.com/matlabcentral/fileex...

circa 6 anni fa | 0

Risposto
how to select the output current in boost converter?
You should find the detailed answer of how to design a boost converter inside this model: https://www.mathworks.com/matlabcentr...

circa 6 anni fa | 1

Risposto
Electric Rail System Model
I do not have this model, but you can check this model and let me know if you have further question: https://www.mathworks.co...

oltre 6 anni fa | 0

Risposto
how Dc DC boost converter with PID can be achieved in simulink.
You might find some portion of the model you are asking for in the two models mentioned below, but off course you will have to a...

oltre 6 anni fa | 0

Risposto
How to design DC-DC boost converter using simulink (Current mode control)
Check out those models: https://www.mathworks.com/matlabcentral/fileexchange/63330-current-controller-dc-dc-bidirectional-con...

oltre 6 anni fa | 1

Risposto
Boost Converter in Simulink
Check this model and compare: https://www.mathworks.com/matlabcentral/fileexchange/63949-voltage-control-dc-dc-boost-converte...

oltre 6 anni fa | 0

Risposto
Need help modeling a Buck/Boost Converter in Simulink/Simscape
Check out those two models for boost and bidirectional dc/dc converter. An explanation can be found in the Simulink model. Those...

oltre 6 anni fa | 0

Risposto
How to Parallel Boost converter to suply dc load
If the PIs are meant to fix the voltage across the 60 ohms resistance. Then, this is a droop control where the load is being sha...

oltre 6 anni fa | 0

Risposto
capacitor and inductor in boost converter
Basically, without them the output of the converter whether it is voltage or current will be square wave, on/ off. Most of loads...

oltre 6 anni fa | 0

Risposto
DC DC Converter with battery as a load
Hi, You need a boost converter to boost the voltage from (16-32V) to 60V, or you can use bidirectional converter, you can use...

oltre 6 anni fa | 2

Risposto
Current mode controlled DC DC boost converter?
Hi, Check this model and let me know if you have further question: https://www.mathworks.com/matlabcentral/fileexchange/63330...

oltre 6 anni fa | 0

Risposto
design of dc dc bidirectional charge controller for lead acid battery in simulink?
Hi, Check out this model: https://www.mathworks.com/matlabcentral/fileexchange/63791-voltage-control-dc-dc-bidirectional-conv...

oltre 6 anni fa | 0

Risposto
How will I simulate a circuit of Bidirectional DC-DC converter fed drive using MOSFETs for electric vehicle system ?
Hello, You can start by checking out this model: https://www.mathworks.com/matlabcentral/fileexchange/63791-voltage-control-dc-d...

oltre 6 anni fa | 0

Risposto
how to draw a simulation model of bidirectional converter??
Check out those two models: https://www.mathworks.com/matlabcentral/fileexchange/63330-current-controller-dc-dc-bidirectional...

oltre 6 anni fa | 0

Risposto
Boost converter in Simulink
This block is not compatible with the rest of the model. Check this model: https://www.mathworks.com/matlabcentral/fileexchan...

oltre 6 anni fa | 0

Inviato


Voltage Control DC/DC Boost Converter
DC/DC Boost Converter can be used to maintain the DC bus voltage

oltre 6 anni fa | 22 download |

Thumbnail

Inviato


DC traction system, Electrical train model
A DC traction system, 2 substations, with a train moving between 3 passenger stations were modeled

oltre 6 anni fa | 30 download |

Thumbnail

Inviato


Current Controller DC/DC Bidirectional Converter
Current Controller DC/DC Bidirectional Converter Model with a detailed description

oltre 6 anni fa | 39 download |

Thumbnail

Inviato


Voltage Control DC/DC Bidirectional Converter
Voltage Controlled DC/DC Bidirectional Converter, multiple Simulink version is uploaded

oltre 6 anni fa | 56 download |

Thumbnail

Risposto
Medium voltage distribution network Simulink model
Check this link: http://www.mathworks.com/matlabcentral/fileexchange/index?utf8=%E2%9C%93&term=ieee

circa 9 anni fa | 2

Risposto
How can I modelize the IEEE 123 Node Feeder on Matlab/Simulink. please help me
Check this link: http://www.mathworks.com/matlabcentral/fileexchange/index?utf8=%E2%9C%93&term=ieee

circa 9 anni fa | 0

| accettato