Statistiche
RANK
38.826
of 288.892
REPUTAZIONE
1
CONTRIBUTI
23 Domande
1 Risposta
ACCETTAZIONE DELLE RISPOSTE
8.7%
VOTI RICEVUTI
1
RANK
of 143.090
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Content Feed
Domanda
Find values of two variables corresponding to query points of two matrices.
If Ithere are 2 equations A(x,y) and B(x,y) that are functions of 2 varibles x, y. Suppose I set some values for x and y as vect...
10 mesi fa | 1 risposta | 0
1
rispostaDomanda
What is the Memory Block actually useful for?
In the Aerospace Blockset example : asbSkyHogg Why are these Memory blocks used? How do they affect the simulation?
circa un anno fa | 2 risposte | 0
2
risposteDomanda
A question about SkyHogg model in Aerospace Blockset
in the example model: asbSkyHogg in this block (asbSkyHogg/Vehicle System Model/Vehicle/3DOF to 6DOF/3DOF to 6DOF/calc alpha_d...
oltre un anno fa | 1 risposta | 0
1
rispostaDomanda
PX4 firmware upload error
I'm having this error while trying to configure the UAV Toolbox Support Package for PX4 Autopilots with my Pixhawk 2.4.8 board. ...
quasi 2 anni fa | 1 risposta | 1
1
rispostaDomanda
How to create a hardware-timed task for NI USB-6363 DAQ?
I'm trying to output an ordinary sinewave from MATLAB via NI USB-6363 DAQ and displaying it on an oscilloscope. The output frequ...
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
Issue with NI USB-6363 DAQ and MATLAB interface
I have an issue outputting an ordinary sinewave from MATLAB via NI USB-6363 DAQ and displaying it on an oscilloscope. The ou...
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
Replace specific line in a text file
Hi everyone, I have a text file (for example: data.dat) as shown below, with a number of lines. data.dat @motion parameter...
oltre 4 anni fa | 1 risposta | 0
1
rispostahow to edit configuration parameters for model to support a connectivity configuration
Hi Hussam, I have seen your comments in Embedded Coder Target for TIVA C, and I'm very interested since I want to conduct a sim...
oltre 5 anni fa | 0
Domanda
Connect Tiva C launchpad with Simulink (PIL)
Hi all, How can I link the TIVA C "TM4C123GH6PM" Launchpad with Simulink?. I want to send a variable from Simulink to Tiva C to...
circa 6 anni fa | 0 risposte | 0
0
risposteDomanda
Import elements of an array from workspace
Hi, I've created this model in Simulink to import elements of an array of waypoints (x,y) from workspace on a sequential basis...
circa 6 anni fa | 1 risposta | 0
1
rispostaDomanda
A Matlab Function: in Matlab Function Block Vs. in Matlab Editor
Hi, I'm using a matlab function (waypoints.m) to generate an array of waypoints. The input arguments are the starting and ending...
circa 6 anni fa | 1 risposta | 0
1
rispostaDomanda
Matlab code works fine as m file but doesn't work when it's called in a Matlab function block in Simulink
Hi, I'm using a matlab function code (waypoints.m) to generate an array of waypoints. The input arguments are the starting and ...
circa 6 anni fa | 1 risposta | 0
1
rispostaDomanda
Insert waypoints into a simulink model
I'm guiding an UAV to land at a specific point on the ground. I have used some waypoints algorithm to create a set of waypoints ...
circa 6 anni fa | 1 risposta | 0
1
rispostaDomanda
How to tune a custom PID block to increase disturbance rejection?
I have created a hand-made PID system on Simulink and I want to tune the gains (the green blocks in the attached image) to give ...
oltre 6 anni fa | 0 risposte | 0
0
risposteDomanda
Why Matlab opens a new session when I double-click a mat file when a session is already open?
Matlab opens multiple sessions everytime I click a mat file. I want them to open in the same session. I have tried *File Associ...
quasi 7 anni fa | 0 risposte | 0
0
risposteDomanda
Trim and linearization a model
Hi I'm using the glider model in Aerosim Blockset to simulate the flight of a gliding vehicle (no engine, no propulsion). I w...
quasi 7 anni fa | 0 risposte | 0
0
risposteDomanda
S- function does not exist
When I try to run a demo Simulink model in the Aerosim Blockset, I got an error "S-Function 'sfunwmm' does not exist" I searche...
quasi 7 anni fa | 2 risposte | 0
2
risposteDomanda
The documentation of NASA HL-20 demo model
Where can I find the documentations of trim, linearization, guidance and control subsystems of the NASA HL-20 lifting body in ae...
quasi 7 anni fa | 0 risposte | 0
0
risposteDomanda
The documentation of NASA HL-20 demo model
Where can I find the documentations of trim, linearization, guidance and control subsystems of the NASA HL-20 lifting body in ae...
quasi 7 anni fa | 0 risposte | 0
0
risposteDomanda
Aerospace Blockset demos run error
In *Matlab R2017a* When I try to run the Aerospace examples model (demos), for example 'asbSkyHogg'.. There are undefined functi...
circa 7 anni fa | 2 risposte | 0
2
risposteDomanda
Convert XYZ in ECEF frame into Navigation frame (ENU)
I'm using a block in Simulink to get XYZ coordinates of an aircraft in ECEF frame from Lat, Long, Alt of a GPS. How can I trans...
circa 7 anni fa | 0 risposte | 0
0
risposteDomanda
Aerodynamics of the Aerosim Blockset Glider model
Hello, I'm working on the glider model in the Aerosim Blockset library. I have some confusion about filling up the aerodynamic ...
circa 7 anni fa | 0 risposte | 0
0
risposteDomanda
How to get the transfer function between any state and the control input from their state space representation?
If we have a system S in state space representation where A= x1 x2 x3 x4 x1 -0....
circa 7 anni fa | 0 risposte | 0
0
risposteDomanda
How can I convert a Simulink PID block into a Matlab code ?
I need to convert a PID block system in Simulink into Matlab code and then into C. Any tips ?
oltre 7 anni fa | 1 risposta | 0