Receive

Receive messages

• 

Libraries:
Simulink / Messages & Events
SimEvents

Alternative Configurations of Receive Block:
Message Receive

Description

The Receive block extracts data from received messages and writes them to the output signal port. If there are no new messages when the block executes, the block uses the Value source when queue is empty value. Receive and Message Receive blocks are identical blocks.

• Select Hold last value to hold data read from the last message.

• Select Use initial value to write default data.

Ports

Input

Port_1 — Input message

scalar | vector | matrix

The input port for the message.

Data Types: single | double | int8 | int16 | int32 | int64 | uint8 | uint16 | uint32 | uint64 | Boolean | enumerated | bus | fixed point

Output

Port_S — Show whether a message was received

scalar

Outputs 1 if the block receives a message successfully, and 0 otherwise.

Dependencies

To enable this port, select the check box labeled Show receive status.

Data Types: double

Port_1 — Output signal

scalar | vector | matrix

Output port for the signal.

Data Types: single | double | int8 | int16 | int32 | int64 | uint8 | uint16 | uint32 | uint64 | Boolean | enumerated | bus | fixed point

Parameters

Use internal queue — Select to use an internal queue

on (default for SimEvents^®) | off (default for Simulink^®)

Select this check box if you use an internal queue to receive messages.

Programmatic Use

Block Parameter: UseInternalQueue

Type: character vector

Values: 'on' | 'off'

Default: 'on'

Overwrite the oldest element if queue is full — Specify queue overwriting policy

on (default for Simulink) | off (default for SimEvents)

Select this check box to choose between two queue overwriting policies.

• If you select the check box, an incoming message overwrites the oldest if the queue is full.

• If you clear the check box, the block does not accept new messages if the queue is full.

Dependencies

This parameter is visible when you select the box labeled Use internal queue.

Programmatic Use

Block Parameter: QueueOverwriting

Type: character vector

Values: 'on' | 'off'

Default: 'on' (for Simulink) and 'off' (for SimEvents)

Queue length — Specify the length of the message queue

16 (default) | scalar

Specify message queue capacity. The queue length can be specified as a positive integer between 1 and 2²⁶-1 (both included).

Dependencies

This parameter is visible when you select the box labeled Use internal queue.

Programmatic Use

Block Parameter: QueueLength

Type: character vector

Values: '16' | scalar

Default: '16'

Queue type — Specify message queue sorting policy

FIFO (default) | LIFO | Priority

The block supports three message sorting policies:

• First-in-first-out (FIFO) — The oldest message in the storage departs first.

• Last-in-first-out (LIFO) — The newest message in the storage departs first.

• Priority — Messages or entities are sorted based on their priority.

  The priority queue can be used only when the Overwrite the oldest element if queue is full check box is cleared.

  Note

  Priority queue accepts only non-bus scalar and it does not support fixed point data type.

Dependencies

This parameter is visible when you select the box labeled Use internal queue.

Programmatic Use

Block Parameter: QueueType

Type: character vector

Values: 'FIFO' | 'LIFO' | 'Priority'

Default: 'FIFO'

Priority order — Specify message queue priority

Ascending (default) | Descending

Choose the direction of sorting messages based on priority.

• Ascending — Messages with smaller priority values appear in front of the queue.

• Descending — Messages with greater priority values appear in front of the queue.

Dependencies

This parameter is visible when you select the box labeled Use internal queue andQueue type > Priority.

Programmatic Use

Block Parameter: PriorityOrder

Type: character vector

Values: 'Ascending' | 'Descending'

Default: 'Ascending'

Show receive status — Show whether a message was received

off (default) | on

Select this check box to show whether a message was received. If this check box is selected the block outputs 1 if it receives a message successfully, and 0 otherwise.

Programmatic Use

Block Parameter: ShowQueueStatus

Type: character vector

Values: 'on' | 'off'

Default: 'off'

Initial value — Set initial data value

[](unspecified) (default) | scalar | vector | matrix

Enter an initial data value for the queue before the arrival of the first message. The default value [](unspecified) is treated as 0 with data type double.

To use this block to initialize a nonvirtual bus signal, specify the initial value as a MATLAB^® structure. For more information about initializing nonvirtual bus signals using structures, see Specify Initial Conditions for Bus Elements.

Programmatic Use

Block Parameter: InitialValue

Type: character vector

Values: '[]' | scalar

Default: '[]'

Value source when queue is empty — Value source for empty queue

Hold last value (default) | Use initial value

Specify the value to receive when received message queue is empty.

• Hold last value (default) — Holds data read from the last message.

  Initially, if the block tries to receive a message and fails, it outputs the initial value.

• Use initial value — Writes default data.

Dependencies

This parameter is visible when you select the box labeled Use internal queue.

Programmatic Use

Block Parameter: ValueSourceWhenQueueIsEmpty

Type: character vector

Values: 'Hold last value' | 'Use initial value'

Default: 'Hold last value'

Sample time (-1 for inherited) — Specify the time interval between samples

-1 (default) | scalar

To inherit the sample time, set this parameter to -1. See Specify Sample Time for more information.

Programmatic Use

Block Parameter: SampleTime

Type: character vector

Values: '-1' | scalar

Default: '-1'

Block Characteristics

Data Types	Boolean | bus | double | enumerated | fixed point | integer | single | string
Direct Feedthrough	no
Multidimensional Signals	yes
Variable-Size Signals	no
Zero-Crossing Detection	no

Alternative Configurations

Message Receive — Receive messages into a queue

The Message Receive block selects the Use internal queue parameter, sets Queue type to FIFO and Queue length to 16.

Libraries:
Simulink / Messages & Events
SimEvents

Extended Capabilities

C/C++ Code Generation

Generate C and C++ code using Simulink® Coder™.

When you generate code for a model that uses a message queue and has multitasking enabled, enable concurrent tasking behavior if that model will be deployed to a multitasking environment. Otherwise, the generated code has the potential for data corruption. You enable concurrent tasking behavior by selecting Allow tasks to execute concurrently on target.

Version History

Introduced in R2016a