Statistiche
RANK
241.008
of 288.900
REPUTAZIONE
0
CONTRIBUTI
15 Domande
0 Risposte
ACCETTAZIONE DELLE RISPOSTE
26.67%
VOTI RICEVUTI
0
RANK
15.705 of 19.494
REPUTAZIONE
7
VALUTAZIONE MEDIA
0.00
CONTRIBUTI
1 File
DOWNLOAD
14
ALL TIME DOWNLOAD
76
RANK
of 143.101
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Content Feed
Domanda
Power Supply current output for data analysis
Hello, We have many power supplies that have been running for the past 15 years. I have access to the power supply output curre...
oltre un anno fa | 1 risposta | 0
1
rispostaDomanda
Importing data from a .mat file into the Sensitivity Analyzer App on Simulink
I have a .mat file that has data that I would like to import into the Sensitivity Analyzer app on simulink to perform additional...
oltre un anno fa | 1 risposta | 0
1
rispostaDomanda
Capturing efficiency of a system while sweeping voltages and duty cycle parameters
I have a simscape simulation model of a power electronics converter and I need to find the optimum parameters to achieve the bes...
oltre un anno fa | 1 risposta | 0
1
rispostaDomanda
Modeling RG220 coaxial cable using a PI section line
I have two parallel RG-220/u coaxial cables which go to a magnet load from a pulse forming network. I recently found out that I ...
oltre un anno fa | 1 risposta | 0
1
rispostaDomanda
Extracting amplitude and frequency component using short time Fourier transform
I need to calculate the capacitance and equivalent series resistance (ESR) of a capacitor in a Boost converter. My boost convert...
quasi 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Three-phase, three-winding transformer parameters
How to calculate the following values in a three-phase, three-winding transformer? I need to model this transformer in MATLAB/Si...
circa 2 anni fa | 0 risposte | 0
0
risposteDomanda
How to create a square wave with different amplitudes?
I need to generate a square wave from -8 to 15 with a frequency of 18 kHz. How can I do this in Simulink?
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
RC snubbers for 12-pulse thyristor bridge
I am trying to simulate an AC-DC power supply (12-pulse thyristor bridge connected in series) with an RC snubber. The real power...
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
Step Down Solar PV High DC Voltage
I have a PV panel which is rated at 5HP. The DC voltage generated by the panel is connected to the DC bus of its respective AC d...
oltre 3 anni fa | 0 risposte | 0
0
risposteDomanda
Computing voltage and current amplitude and average power
Hello, I have three sinusoidal waveforms namely, voltage, current, and power acquired using an oscilloscope which I then have c...
oltre 3 anni fa | 1 risposta | 0
1
rispostaDomanda
How to model a Klystron in Matlab/Simulink?
Hello all, I am trying to model a Klystron which is a specialized linear-beam vacuum tube that is used as an amplifier for high...
oltre 4 anni fa | 0 risposte | 0
0
risposteDomanda
How should the change in delta V (change in voltage) look like in a perturb and observe algorithm?
Hello all, I am currently working on an IEEE paper which is about extracting maximum power under partial shading of PV panels...
quasi 6 anni fa | 0 risposte | 0
0
risposteDomanda
How do I plot this graph on MATLAB?
Dear all, I am having difficulty in plotting this particular graph on MATLAB. I know that I am supposed to use an if and/or f...
quasi 6 anni fa | 1 risposta | 0
1
rispostaDomanda
How to create a Network Node Incidence Matrix?
Hello guys, I am currently working on an IEEE paper which uses the Data of an IEEE-24 Bus System. I need to construct a Network...
oltre 6 anni fa | 2 risposte | 0
2
risposteDomanda
How to reduce the size of a 144x1 Vector to a 72x1 Vector by adding two consecutive elements in the Original Vector?
Hello all, I have a vector which has the dimensions of 144x1. The numbers in the vector repeat after every sixth row. For examp...
oltre 6 anni fa | 1 risposta | 0