photo

Ayham Aljawabrah


Last seen: 1 giorno fa |  Attivo dal 2019

Followers: 0   Following: 0

Statistica

  • Thankful Level 2
  • Thankful Level 1
  • Knowledgeable Level 1
  • First Answer
  • First Review

Visualizza badge

Feeds

Visto da

Risposto
I am having problems with the install_addon.m
When I downloaded the function, it has the name 'installaddon', not 'install_addon'. Make sure of the function name, and if it i...

24 giorni fa | 0

Domanda


Two different models for the stepper motor in Simscape stepper motor blocks
I found in Simscape two differnt blocks for the stpper motor SM block 1 SM block 2 Before going to the question, In t...

6 mesi fa | 1 risposta | 0

1

risposta

Domanda


Problem in Stepper Motor block Parameters with predefined parametrization
I am using the stepper motor block provided in the Simscape toolbox R2020b. I used the predefined parametrization from the provi...

6 mesi fa | 0 risposte | 0

0

risposte

Domanda


Modeling of hybrid stepper motor (HSM) using Simulink
Hi all, I am trying to build a Simulink model for HSM, using the math model in photo p1. This model is the same seen in Matlab ...

oltre un anno fa | 0 risposte | 0

0

risposte

Domanda


How to Extract X,Y,Z vectors from grid data?
I have the below data from contour grid, but I am not sure how to deal with it, the data are more than 3000 rows. I have two que...

oltre un anno fa | 1 risposta | 0

1

risposta

Domanda


Stateflow shows a dimension error for an output port?
I am using Statefloe, specifically, Simulink based state and experiencing a problem. My Model have 5 states and uses one simulin...

quasi 3 anni fa | 0 risposte | 0

0

risposte

Domanda


How to find intersection of several data sets?
I have 50 sets of (x, y) points, and each set contains handreds of points, I am trying to find the intersection points between t...

circa 3 anni fa | 1 risposta | 0

1

risposta

Risposto
I wanted the matlab to show 5 places after the comma.
Hello lucass! Try, vpa c=1/3 vpa(c,5)

oltre 3 anni fa | 0

| accettato

Risposto
How to solve a system of equations mixing non-linear ODE and non-linear "simple" equations?
The solvers usually able to solve index-1 DAE, not all the equations are apperent but you have too many variables you mostly nee...

oltre 3 anni fa | 0

Risposto
Multiple variable inputs for a function
The logical order of the code is not correct and the function definition as well. A guide code can help you to reconstruct your...

oltre 3 anni fa | 0

Domanda


Interface Simulink based clutch device with Simscape driveline loop
Hello Everyone! I am trying to simulated the gear change behavior in a vehicle transmission using Simulink and Simscape drive...

oltre 3 anni fa | 1 risposta | 0

1

risposta

Domanda


Spatial contact force block
Hi I am trying to build a model for the dog clutch with Simscape multibody as shown in the below figure. each side can rotate ...

oltre 3 anni fa | 1 risposta | 0

1

risposta

Domanda


How to convert 3d scattered points to coloured map?
I have three column vectors xp, yp, zp, where each column set of these vectors form the coordinate for a point in 3d space. I us...

quasi 4 anni fa | 1 risposta | 0

1

risposta

Domanda


How to fix cropped legend of non-default sized plot figure?
Hi MATLAB Users! I have to prepare some plot using MATLAB to a predetermined size. I made a figure with the default size then r...

quasi 5 anni fa | 1 risposta | 0

1

risposta