English
Statistica
0 Domande
18 Risposte
RANK
2.696
of 301.273
REPUTAZIONE
22
CONTRIBUTI
0 Domande
18 Risposte
ACCETTAZIONE DELLE RISPOSTE
0.00%
VOTI RICEVUTI
1
RANK
of 173.726
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
The Display block and Scope block of Simulink did not work when running external mode to tuning
Hi , Can you please check if "Use a dedicated timer to improve time stamp accuracy" is disabled. If not then go to (ctrl+E) ...
23 giorni fa | 1
| accettato
Touchgfx integration with Simulink in matlab
Hi Jerry, Refer: SIMULINK with STM32 - MATLAB Answers - MATLAB Central Thanks, Madhu
circa 2 mesi fa | 0
Problem with UDP communication while configuring stm32nucleo using cubemx in Simulink
Please refer STM32H753ZI: Simulink UDP/TCP blocks fail due to Ethernet DMA buffer address requirement (0x30040200) - MATLAB An...
circa 2 mesi fa | 0
STM32H753ZI: Simulink UDP/TCP blocks fail due to Ethernet DMA buffer address requirement (0x30040200)
Hi, For the R2024b release, the supported version of CubeMX is 6.4.0. It is strongly recommended to use this version with MATLA...
circa 2 mesi fa | 0
Registration of STM32CubeMX Tool Without Internet-Based Third-Party Tools Installation
Hi, Kindly contact Technical Support for further assistance: https://in.mathworks.com/support/contact_us.html Thank you, Mad...
2 mesi fa | 0
LIN support for STM32 microcontroller series
Hi, Currently, LIN communication support is not available as a built-in block for STM32 . However, you can create your own cus...
3 mesi fa | 0
| accettato
SIMULINK with STM32
Hi Jerry, As Nidhi mentioned, display peripherals are currently not supported at present. However you can use custom code bloc...
4 mesi fa | 0
STM32F4xx Error:External Mode Open Protocol Connect command failed
Hi, It looks like you’re experiencing an external mode connection failure, which might be caused by selecting the wrong COM po...
7 mesi fa | 0
STM32 NUCLEO H753ZI Mqtt Simulink block is not sending.
Hi, Kindly contact Technical Support for further assistance: https://in.mathworks.com/support/contact_us.html Ensure that the...
8 mesi fa | 0
Unable to Programm stm Microcontroller.
Hi, There can be two workaround for the above issue: Instead of going through the Hardware Setup Screen, can you download the ...
circa 2 anni fa | 0
Gettting an error when trying to run the "Exchanging WiFi Data and Using ThingSpeak with STM32L475VG Discovery Board" MatLab example
Hi , I tried running the example at my end. It works fine without any error. Make sure the wifi setup and configuration paramet...
circa 2 anni fa | 0
Waijung Blockset Cannot Be Compiled
Hi Serhat, Wijung blockset is not supported by MathWorks , please post in respective channel for the same. Alternatively, you c...
oltre 2 anni fa | 0
Code generation from Simulink to STM32F103 Processor.
Hi Nandini, STM32/MAT target is obsolete and not supported with the latest versions of MATLAB as mentioned here: https://www.st...
oltre 2 anni fa | 0
| accettato
Embedded Coder support packages for STM32
Currently it is not supported , but you can develop the custom blocks depending on requirement. As device driver development is...
oltre 2 anni fa | 0
Embedded Coder support package for STM32
Currently it is not supported , but you can develop the custom blocks depending on requirement. As device driver development is...
oltre 2 anni fa | 0
STM32F411 Discovery board Blink LED program error
Hi, The STM32F4-Discovery board, specifically utilizing the STM32F407VG microcontroller, is officially supported according to t...
oltre 2 anni fa | 0
| accettato
FPGA in the Loop minimum clock frequency
To get FPGA simulation with a small clock frequency, try increasing oversampling factor of the design. The Oversampling factor d...
oltre 3 anni fa | 0
| accettato
Need help with Fourier Transform of a function
For this case, it is not necessary to get x(t). If y(t) = x(t) .[cos(t/2) + cos(3t/2)] and if x(jw) is known , then using conv...
quasi 4 anni fa | 0
