Statistica
RANK
90.780
of 300.392
REPUTAZIONE
0
CONTRIBUTI
12 Domande
2 Risposte
ACCETTAZIONE DELLE RISPOSTE
8.33%
VOTI RICEVUTI
1
RANK
of 168.373
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Domanda
How do I use Simulink Coder to build a Simulink model and generate the necessary header files that seem to be missing?
Hello, I’m trying to build a simple LQR block diagram using Simulink Coder for deployment on a Raspberry Pi board. However, du...
3 mesi fa | 1 risposta | 0
1
rispostaDomanda
How to implement an LQR controller when the system's state variables and control inputs have different units?
Hello, I am wondering how to implement an LQR controller when the state variables and control inputs have different units. For...
9 mesi fa | 1 risposta | 0
1
rispostaDomanda
How to implement MPC when the number of states is greater than the number of outputs?
I want to implement MPC using MATLAB's Model Predictive Control Toolbox. When I checked the official MATLAB website, I found on...
9 mesi fa | 1 risposta | 0
1
rispostaHow to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...
9 mesi fa | 0
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...
10 mesi fa | 1
Domanda
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I want to execute the example of Send and Receive Serial Data Using PX4 Autopilots Support Package. I followed the step...
10 mesi fa | 2 risposte | 0
2
risposteDomanda
How can I execute a Simulink block only when a specific condition is met?
Hi all, Is there a way to execute the following block diagram only when a certain condition is satisfied (e.g., when a joysti...
12 mesi fa | 1 risposta | 0
1
rispostaDomanda
How to use "StabilityThreshold" estimation option in greyest function?
Hello, To predict the lateral equations of the H4 Hercules using a greybox model, I defined the model function as follows and s...
circa un anno fa | 1 risposta | 0
1
rispostaDomanda
Problem Occurred While Using MATLAB System Identification Toolbox
Hello, I am currently performing system identification using the System Identification Toolbox after extracting the response dat...
circa un anno fa | 1 risposta | 0
1
rispostaDomanda
Inquiry about IP address and port number for UDP Send and UDP Receive block
Hello all, I have a question about the IP addresses and port numbers for the UDP Send and UDP Receive blocks. When sending and ...
circa un anno fa | 1 risposta | 0
1
rispostaDomanda
How to store object(like udp object) in level-2 s-function?
Hello all, I want to send control input from Matlab to FlightGear and receive aircraft data from FlightGear to Matlab with UDP ...
circa un anno fa | 1 risposta | 0
1
rispostaDomanda
How to calculate minimum singular value of I+L and I+inv(L) for MIMO system?
Hello, I want to calculate minimum singular value for MIMO system, and here is an example %% A = [0.1873 0.8403 -0.6003 -2.1...
quasi 2 anni fa | 1 risposta | 0
1
rispostaDomanda
What's the difference between two command?
Hello, In general, the command of nyquist plot is nyquist(sys,omega), but an example of textbook the command of nyquist is nyqu...
quasi 2 anni fa | 1 risposta | 0
1
rispostaDomanda
How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...
quasi 2 anni fa | 0 risposte | 0
