Risposto
vpa, simplify, solve, etc don't fully simplify symbolic function.
l = 50; a = 10; W = 1200; syms Q(z); Q(z) = 1200 + 56*z - 2.5*z^2; R = - int(Q(z), [0 l]) + W; syms F1(z) F2(z) F3(z); F1...

12 mesi fa | 0

Risposto
what is this block called
That is a Memory block.

12 mesi fa | 1

| accettato

Risposto
Transfer function model from block diagram
The easiest way, IMO, is to use connect. Feel free to post back here if you still have questions after reading the doc page and ...

12 mesi fa | 0

| accettato

Risposto
Help with MATLAB symbolic toolbox
Hi Scott, See below for solution % Set up symbolic variables syms t C1 C2 % Set up parameters K = 2.2167e+06; M = 45.96; ...

circa un anno fa | 0

Risposto
fftshift implementation in Simulink
fftshift is extended to code generation. Assuming the data output from the FFT block is in linear order, you can call fftshift f...

circa un anno fa | 0

Risposto
ECEF 6DOF block - position calculation
Hi Thomas, As far as I can tell, the translational equations in the Algorithms section of the documentation page 6DOF ECEF (Qua...

circa un anno fa | 0

Risposto
Data extraction/split from table
Hi Daher, Start with findgroups identify the unique rows in the table and map each row to a unique row. T = readtable('art_fil...

circa un anno fa | 2

Risposto
Does enu2ecefv make any assumptions about the ellipsoid?
Hi Eitan, See Vectors in 3-D Coordinate Systems for a brief explanation.

circa un anno fa | 0

| accettato

Risposto
How to calculate only several frequency with FFT ?
If the desired frequenices are a subset of those that correspond to the DFT as computed by fft, I'd imagine in many cases there ...

circa un anno fa | 1

Risposto
how to search parameter with specific name under the simulink system
Check out Simulink.findVars

circa un anno fa | 0

| accettato

Risposto
possibility to create "Enbaled" subsystem
One option would be to create the subsystem as an Enabled subsystem and then control the enable port with a signal that you cont...

circa un anno fa | 0

Risposto
steady plot end with different rate of rise question
Hi fima, The functions being plotted are of the form syms y_i(x) r_i disp(y_i(x) == exp(r_i*x) - 1) Why should y_i(x) be the...

circa un anno fa | 0

Risposto
Serious Problem with FiltFilt Function
The filter is not unstable. Rather, the issue is an interaction between how filtfilt works and the implementation of the biquadr...

circa un anno fa | 0

Risposto
Could not define a data in matrix form in model workspace ( for simulation)
Based on the limited description, I'm not quite sure how you'd like to run multiple iterations of a simulation for different par...

circa un anno fa | 0

Risposto
How to plot a string signal/array?
I don't believe there is a built-in function to plot a string vector against a numeric vector in any fashion, much less to produ...

circa un anno fa | 1

Risposto
readtable does not import headers properly while reading csv file
dbtype data.csv T = readtable('data.csv','LeadingDelimitersRule','keep','ReadVariableNames',true); T(1:5,:)

circa un anno fa | 0

Risposto
no data in the data browser when i use model linearizer in simulink
See this Question and Answer.

circa un anno fa | 0

Risposto
unable to identify and simulate a function block
Try using a Constant block and set the block parameter "Constant value" to 2*Kr*lfc. Can do the same for the Kr*lfc term as well...

circa un anno fa | 0

| accettato

Risposto
How to change the default x-axis unit in a Bode diagram to Hertz?
ctrlpref allows one to change the default units for frequency axis when plotting with bode and bodeplot (among other defaults in...

circa un anno fa | 2

Risposto
Deconvolution of two Bragg Curves
D = dir; D(3).name T1 = readtable(D(3).name); T1.Properties.VariableNames VarName2 = T1.Var2; D(4).name T2 = readtable(D(4...

circa un anno fa | 0

| accettato

Risposto
Which exponential option block: fcn vs math function, is more accurate in a Simulink model?
In general u/fc (top path), is not exactly the same as u*(1/fc) (bottom path) in floating point. Example: rng(100) u = rand; ...

circa un anno fa | 0

| accettato

Risposto
Why does this special case for associativity of a matrix product with a hadamard product hold true?
Hi Clay, If you're willing to accept (or show, which I think would be straight forward) that, in Matlab, matrix .* row is equal...

circa un anno fa | 2

Risposto
Implementing Z-Transform of -a^n*heaviside(-n-1)
syms a n z Assume is an integer for clarity assume(n,'integer'); To get the expected result, we have to ensure the correct va...

circa un anno fa | 1

Risposto
How to Solve a System of Equations for symfun Objects?
I took a shot. Here's a start, doesn't do any error checking, assumes that there is one valid solution .... syms R(s) e(s) Y(s)...

circa un anno fa | 0

Domanda

How to Solve a System of Equations for symfun Objects?
Suppose I have a system of equations: syms R E Y G eq1 = Y == G*E; eq2 = E == R-Y; Solve for Y and E in terms of R sol = so...

circa un anno fa | 2 risposte | 0

2

risposte

Risposto
question about dely lines
One can attack this symbolically if the parameters in the problems aren't known. If they are, one can proceed numerically using ...

circa un anno fa | 0

Risposto
How to use the diagonal symbol matrix？
Need to specify the vars explicitly if defined individually syms a1 a2 a3 A = diag([a1,a2,a3]) M = matlabFunction(2*A,'Vars',...

circa un anno fa | 1

| accettato

Risposto
how can plot the region of convergence?
Since 2024a, radiusregion looks like a reasonable approach to get started. For example, suppose the region of convergence is 0....

circa un anno fa | 0

Risposto
What is default Mu for Vehicle Body 3 DOF block?
As best I can tell, if the [mu_r, mu_f] vector is not specified externally, then the block uses the parameter specified in Nom...

circa un anno fa | 0

| accettato

Risposto
Why the filter has no output?
The function filter is only applicable for a discrete-time filter, not an analog filter. If you want to simulate the output from...

circa un anno fa | 0