photo

Mike Bardill


Rolls-Royce Plc

Last seen: circa 4 anni fa |  Attivo dal 2013

Followers: 0   Following: 0

Messaggio

Statistica

All
  • Thankful Level 1
  • Solver

Visualizza badge

Feeds

Visto da

Domanda


Getting timing closure for HDL Coder IP with multicycle paths
I have created an IP component with HDL Coder and I have integrated this into a Vivado project but I am struggling to get timing...

oltre 5 anni fa | 1 risposta | 0

1

risposta

Domanda


ZedBoard FIL example does not run with R2018a
I have been running the example "Verify HDL Implementation of PID Controller Using FPGA-in-the-loop" on a ZedBoard using R2018a....

quasi 6 anni fa | 0 risposte | 0

0

risposte

Risolto


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

quasi 6 anni fa

Domanda


Estimating the latency of a custom IP block in HDL Coder
I have a Simulink design that I want to build into a custom IP block to deploy on a Zynq FPGA target using HDL Coder. The conce...

circa 6 anni fa | 1 risposta | 0

1

risposta

Domanda


sldrtkernel -install fails on Windows 7 Home Premium (r2016b)
With r2016b when I try to install the Simulink Desktop real-Time Kernel on Windows 7 Home Premium I get the following error. Th...

oltre 8 anni fa | 2 risposte | 0

2

risposte

Domanda


How to run model on specific CPU on ZED board
When I build a model for the ZED board Zynq target and do 'deploy to hardware' the target code always runs on CPU 0. A 'top' com...

oltre 8 anni fa | 0 risposte | 0

0

risposte

Domanda


ZED board clock speed
Is there a way to find out what clock speed the ARM CPUs are running at when the board is booted using the Linux kernel that com...

oltre 8 anni fa | 0 risposte | 0

0

risposte

Domanda


Static code metrics report cannot be created in embedded coder
I have a Simulink model that I run in PIL mode on a C6713 DSK target board. I have selected the option to create a static code ...

circa 9 anni fa | 2 risposte | 5

2

risposte

Domanda


PIL Mode Function Level Profiling with ezdspF28335 crashes Matlab
I am using R2013a to do some PIL mode running with the ezdspF28335 board. If I ask for 'task' level profiling in the configurat...

circa 10 anni fa | 0 risposte | 0

0

risposte

Domanda


Static code metrics report not created for ezdspF28335 project
I am working with the ezdspF28335 development board and embedded coder with version R2013a. The project uses Code Composer 5.5 ...

circa 10 anni fa | 1 risposta | 1

1

risposta

Domanda


How to create embedded Linux target main using ert.tlc rather than idelink_ert.tlc
We would like to be able to generate code for an embedded Linux target but use ert.tlc rather than idelink_ert.tlc. The model w...

circa 10 anni fa | 0 risposte | 0

0

risposte

Domanda


Linux UDP Send block fails to send to broadcast address
I have a Simulink model that generates target code to run under Embedded Linux (3.3.0) on a target OMAP-L138 LCDK board. The mo...

oltre 10 anni fa | 1 risposta | 0

1

risposta

Domanda


How can I create code for an embedded Linux target with Simulink hosted on Windows?
I want to be able to create code a multitasking embedded Linux target from Simulink hosted on Windows. The Windows machine does...

oltre 10 anni fa | 1 risposta | 0

1

risposta

Domanda


PIL simulation fails with OMAP-L137 target board
I am attempting to run a PIL mode simulation with r2013a using a Spectrum Digital OMAP-L137 target board. I am using Code Compo...

circa 11 anni fa | 0 risposte | 0

0

risposte