How to separate signals with diffrent frequencies

21 visualizzazioni (ultimi 30 giorni)
t = linspace(0, 1, 1001);
x=sin(2*pi*t*3) + sin(2*pi*t*6) + sin(2*pi*t*10)+sin(2*pi*t*13)+sin(2*pi*t*20)+sin(2*pi*t*50)+sin(2*pi*t*100)+sin(2*pi*t*200);
% my signal with frequencies 3,6,10,13,20,50,100,200 KHz
sigma=0.1;
y=x+randn(size(x)).*sigma; % adding noise
I filtered the signal using fft.
I want to separate signals.
Eg : from my original signal, I want a signal with frequency range say 3 to 8 KHz, another signal say from 100 to 200 KHz. How can I separate them and display those signals.How can I do this. Anybody Please help me to solve this.?
  2 Commenti
mouh nyquist
mouh nyquist il 1 Gen 2015
you must read about chebishev and butter filter
aarthi arunachalam
aarthi arunachalam il 11 Mar 2016
i too want to seperate certain frequency range from my original signal. can you help me?

Accedi per commentare.

Risposta accettata

Shoaibur Rahman
Shoaibur Rahman il 1 Gen 2015
Add the following lines of code at the bottom of your code (after y=x+randn(size(x)).*sigma;):
ffty = fft(y);
ffty = abs(ffty(1:ceil(length(y)/2)));
ffty(ffty<100)=0;
[~,locs] = findpeaks(ffty);
freqs = (locs-1)/t(end)
signal_1 = sin(2*pi*t*freqs(1))+sin(2*pi*t*freqs(2))+sin(2*pi*t*freqs(3)); % 3-10
signal_2 = sin(2*pi*t*freqs(6))+sin(2*pi*t*freqs(7)); % 50-100
subplot(211), plot(t,signal_1)
subplot(212), plot(t,signal_2)
  10 Commenti
Shoaibur Rahman
Shoaibur Rahman il 1 Gen 2015
Modificato: Shoaibur Rahman il 1 Gen 2015
Use any sinusoidal function to generate a signal with that frequency, and then plot that against time. For example:
t = .....
out1 = sin(2*pi*f1*t);
out2 = cos(2*pi*f2*t);
etc....
This is just from the Fourier analysis, that states any signal (with some criteria) can be represented as summation of infinite sinusoidal functions. So, to represent only one frequency, use one sinusoidal function, or to represent multiple frequency components, use summation of multiple sinusoidal functions with those frequencies.
Srey
Srey il 1 Gen 2015
Thank you so much..It works.:)

Accedi per commentare.

Più risposte (1)

Pourya Alinezhad
Pourya Alinezhad il 1 Gen 2015
1-you can use several filters with different center frequencies (chebishev or butter filter)
h = fdesign.bandpass('N,F3dB1,F3dB2', N, Fc1, Fc2, Fs);
Hd = design(h, 'butter');
filter (Hd,input_signal);
2- you can use an adaptive filter and feed the signal and the desired signals to it (LMS filter).
  2 Commenti
Srey
Srey il 1 Gen 2015
I want a signal with freq range:say 3-10Hz and another signal with freq say 50-100. I want to plot them separately.How can be done from my original signal
Pourya Alinezhad
Pourya Alinezhad il 1 Gen 2015
assign Fc1, Fc2 values as 3 and 10Kz for a filter. then make another filter with 50 to 100 kHz spectrum.

Accedi per commentare.

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by