figure not coming up
2 visualizzazioni (ultimi 30 giorni)
Mostra commenti meno recenti
taher azim
il 27 Mar 2017
Commentato: Image Analyst
il 28 Mar 2017
I have written a code in which i have created a rectangular surface using patch command and i m rotating this surface about z axis using the angles i get from my mobile's gyro using udp object.But as irun the code no errors show up but also there is no figure coming up.My code is
instrreset
a=[1 ,-1 ,-1, 1, 1];
b=[1 ,1 ,-1, -1,1];
z=zeros(1,5);
x=zeros(1,5);
y=zeros(1,5);
%Creating UDP object UDPComIn=udp('192.168.173.154','LocalPort',12345); set(UDPComIn,'DatagramTerminateMode','off')
while 1
fopen(UDPComIn);
csvdata=fscanf(UDPComIn);
scandata=textscan(csvdata,'%s %f %f %f %f %f','Delimiter',',');
data=[scandata{4},scandata{5},scandata{6}];
fclose(UDPComIn);
alph=data(1);
for i=1:1:4
t1=[cosd(alph) ,(-sind(alph));sind(alph) ,cosd(alph)];
k=[a(i); b(i)];
m=t1*k;
x(i)=m(1);
y(i)=m(2);
x(5)=x(1);
y(5)=y(1);
end
view(3);
patch(x',y',z');
xlabel('XXX');
ylabel('YYY');
zlabel('ZZZ');
k=k+1;
%CodeEnd
end
but when i run the same patch command while not receiving data from udp just giving angles through for loop it shows no error and figure is also visible.Can anyone plz help me with this problem?
1 Commento
Adam
il 27 Mar 2017
You should create a figure explicitly and refer to the axes explicitly when you create the patch e.g.
hFig = figure; hAxes = axes( hFig );
patch( hAxes, x', y', z' );
It may not be the cause of your problem but it is good practice for making sure you avoid bugs similar to this or have things plotting where you don't expect them.
Risposta accettata
Image Analyst
il 27 Mar 2017
Try putting a
drawnow; % Force refresh/repaint of the screen.
just after you call zlabel().
2 Commenti
Image Analyst
il 28 Mar 2017
Like the comment says, it forces a repaint of your GUI. If you don't get that, then the message to repaint the GUI window will be sort of deferred until your other compute-intensive stuff finishes. For example if you were in a loop where it computers a new curve and updated a plot 1000 times, then it might wait on updating the plot until the computations were done and then finally get around to updating the display 1000 times, but that would happen so fast that you wouldn't see them all and you just see the final last result. By putting drawnow in there, it forces it to deal with the repainting right then and then, and not put it off to do other stuff in advance.
Più risposte (1)
Jan
il 27 Mar 2017
Modificato: Jan
il 27 Mar 2017
As far as I understand this must mean, that this code does not finish:
UDPComIn=udp('192.168.173.154','LocalPort',12345);
set(UDPComIn,'DatagramTerminateMode','off')
fopen(UDPComIn);
csvdata=fscanf(UDPComIn);
fclose(UDPComIn);
Did you try to run it outside the loop?
2 Commenti
Vedere anche
Categorie
Scopri di più su Lighting, Transparency, and Shading in Help Center e File Exchange
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!