Mukul Choudhury
MathWorks
Followers: 0 Following: 0
Statistica
0 Domande
20 Risposte
RANK
6.174
of 301.481
REPUTAZIONE
8
CONTRIBUTI
0 Domande
20 Risposte
ACCETTAZIONE DELLE RISPOSTE
0.00%
VOTI RICEVUTI
2
RANK
of 174.744
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Trouble while generating two SOC triggers (CTR=0 and CTR=PRD) with their respective ISRs on Microcontroller TI F28388D
HI, Can you please share the source of the code. Is this code generated froma Simulink model? If it is a manually hand writte...
2 giorni fa | 0
3-phase Sine PWM Inverter providing Asymmetric Voltage waveform with F28379D ePWM
Hi, Please synchronise the ePWM counters for all the three legs. 1) Send a synchronisation pulse from ePWM1 to other ePWMs. Yo...
6 giorni fa | 0
Unable to add signals to Code Mappings for TI C2000 CLA Task
Hi, Please select the signal that you want to add to the Code Mappings editor. Pause on the ellipsis that appears above or bel...
6 giorni fa | 0
TMS320F28379D/TMS320F28335: How to do a five PWM signals with dead time and logic gates?
Hi @Lucas, You may need to use the c2000 ePWM (https://www.mathworks.com/help/ti-c2000/ref/epwmtype14.html) blocks to generate ...
circa un mese fa | 0
DRV8305EVM: nFault led
Hi, Could you please verify the ADC offsets and HALL calibration offset value. 1) You can run the open loop motor control exam...
circa un mese fa | 0
Increasing PWM frequency for Sensorless FOC Example
Hi Jarek, As you increase the PWM frequency, the controller sample time will reduce which may lead to an overrun. Please check ...
circa un mese fa | 0
Speed command spikes during host-controlled ramp on F28069M dual-motor dyno model
Hi Jonathan, 1) SCI blocks are driver blocks designed for discrete data streaming. You can get smotther ramp by reducing the sa...
circa un mese fa | 0
how to use two carriers for epwm1a module.
Hi Mandvi, Two carrier cannot be generated for a specific ePWM module in TI C2000 Processors. You may need to change the modula...
circa un mese fa | 0
Can we deploy Field-Oriented Control of PMSM Using Reinforcement Learning on TI F28379D LaunchPad ?
Hi Aizaz, OpenMP is not supported in TI C2000 devices. Check this post for more info: https://e2e.ti.com/support/microcontroll...
2 mesi fa | 0
PMSM FOC Hall sensor input for custom GPIO pin configurations
Hi Bhagyesh, 1.ECAP inputs in F20049C are fed by Input X-BAR. Hence you can route any GPIO to eCAP inputs. In order to change ...
2 mesi fa | 0
How can I create SPWM from ePWM blocks for C2000 in Simulink?
Hi, In Sinusoidal PWM, the pulse width will follow sinusoidal pattern i.e. it increases and reaches maximum and then starts r...
8 mesi fa | 0
Missing EPWM features in C2000 Blockset
Hi Aditya, You can make use of Register Read/Write block to make the above register settings. Please check the below link for ...
10 mesi fa | 0
TI F28379D Serial Communication to other Systems
Hi Timo, Please refer to the following example on serial communication: https://in.mathworks.com/help/ti-c2000/ug/serial-commu...
circa un anno fa | 0
How to switch off all 6 MOSFETs (6SO) with ePWM block from C2000 Motor Control Blockset?
Hi, You can ePWM trip zone unit to turn the ePWMs off. Hope this helps. Thanks, Mukul
quasi 2 anni fa | 0
How can I read analog COS and SIN voltages with LAUNCHXL-F28069M?
Hi, The example mentioned by you uses the TI TMDSRSLVR - Resolver EVM kit. This resolver uses a level shifter and a gain ampli...
oltre 2 anni fa | 0
MATLAB HARDWARE , EXTERNAL MODE
Hi, Please refer to the following motor control and power examples that are shipped along with C2000 Microcontroller Blockset: ...
oltre 2 anni fa | 0
CLA compliation issue usin F28388D on simulink 2022a
Hi Aniket, This issue comes if your model calls any math function inside CLA. Please check if there is any call to a math funct...
quasi 3 anni fa | 2
Simulink Texas Instruments F28388D CLAerror: cannot open source file "cla_header.h"
Hi Maximilian, cla_header.h is a header file where the signals and data stores to be stored in CLA storage classes are declare...
oltre 4 anni fa | 0
| accettato
Error using the C2000 CLA
Hi Balint, The CLA does not support sine function and has its own sine function defined in CLAMath Library provided by TI. In ...
oltre 4 anni fa | 0
Simulink for Texas Instruments C2000 microcontrollers CLA: cannot open source file "cla_header.h" in the LAUNCHXL-F28379D
Hi Gabriel, cla_header.h is the file where the data stores, signals and states accesible by cla are declared. Could you please ...
quasi 5 anni fa | 0
