Statistiche
RANK
95.819
of 288.913
REPUTAZIONE
0
CONTRIBUTI
30 Domande
7 Risposte
ACCETTAZIONE DELLE RISPOSTE
13.33%
VOTI RICEVUTI
0
RANK
of 143.107
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Content Feed
Domanda
plot range of freq on unit circle
Hi I want to plot a range of freq 10 k to 1 M Hz on unit circle How can I do that best regards Uzmeed
2 mesi fa | 0 risposte | 0
0
risposteDomanda
SoC bulider taking too long in synthesis
Hi I was trying to build Transit receive example in SoC builder following instruction given in the help. All went good but a...
12 mesi fa | 0 risposte | 0
0
risposteDomanda
Covariance data set size
Hi Is there any data size limit for calculating covariance matrix. Also how does it effect adding data set samples while ca...
quasi 3 anni fa | 0 risposte | 0
0
risposteDomanda
Simulink Fixed point tool
Hi I have developed an application in system generator . I also had a reference .m code which I used to verify the outputs o...
circa 3 anni fa | 0 risposte | 0
0
risposteDomanda
exporting system generator ip to vivado ip catalog
Hi I have sucessfully created system generator ip and apparently sucessfully imported it in Vivado Should this IP give same...
oltre 3 anni fa | 0 risposte | 0
0
risposteMUSIC algorithm for direction of arrival
Thank you Shunichi I know the theory of MUSIC well and that it is a spatial method for AoA estimation My question is that AOA ...
circa 4 anni fa | 0
Domanda
MUSIC algorithm for direction of arrival
I just need to ask is MUSIC algorithm a phase comparison technique? regards Uzmeed
circa 4 anni fa | 3 risposte | 0
3
risposteDomanda
converting a vector input to scalar
Hi I have a 3x3 matrix input. I assign it to some variables to make 7x1 variable (appending zeros) I need to use it in sim...
oltre 4 anni fa | 1 risposta | 0
1
rispostacalculate snr of digital signal
Thanks Daniel All my input are cloumn vectors data_in is a single colum vector similarly diff again a column vector that I ...
oltre 4 anni fa | 0
Domanda
calculate snr of digital signal
Hi I have a data stream say data_in Its maximum is data_max and min is data _min means that data_in may vry between data_m...
oltre 4 anni fa | 2 risposte | 0
2
risposteDomanda
spectrum peak search using eigen values
Hi I am implementing MUSIC algorithm for DOA estimation (in Vivado ) and then verifying the code with Matlab i am done wit...
oltre 4 anni fa | 0 risposte | 0
0
risposteAngle of Arrival for UCA
Hi HTH I did the same but the very first two lines of the document are making me confused the confusion is the same i mentio...
quasi 5 anni fa | 0
Domanda
Angle of Arrival for UCA
Hi I need to implement the angle of arrival for UCA From the matlab available function I have seen that root MUSIC algorithm ...
quasi 5 anni fa | 2 risposte | 0
2
risposteDomanda
co-variance Matrix formation
Hi I have 6 row matrix of size 1x6 I need to calculate the co variance of all the matrices but cov command only taking two ma...
quasi 5 anni fa | 0 risposte | 0
0
risposteDomanda
Error in output - simulink xilinx blockset
I had been using Matlab2016a for the development of my Application. (attached) When I run them seperately both modules are work...
circa 5 anni fa | 0 risposte | 0
0
risposteDomanda
Convert negative decimal into binary
Hi I need to convert an array of fractinal number that contains mix of negative and positive numbers into format of UFix_12_0 ...
circa 5 anni fa | 0 risposte | 0
0
risposteDomanda
what is the theoretical difference between music and root music algorithm
Hi If someone please explain that what is the theoretical difference between music and root music algorithm for DOA estimation ...
circa 5 anni fa | 0 risposte | 0
0
risposteDomanda
reading at UCA elements
Hi I need to receive the signal at different elemnents of UCA I am using the following code sUCA = phased.UCA('...
circa 5 anni fa | 1 risposta | 0
1
rispostaDomanda
simulating RWR in R2016a
hi can the example given at https://ww2.mathworks.cn/help/phased/examples/signal-parameter-estimations-in-a-radar-warning-re...
circa 5 anni fa | 2 risposte | 0
2
risposteDomanda
4 tap moving averaging filter
Hi for a 4 tap moving averaging filter is following correct s=1000; >> x=randn(1,s); >> b=[0.25,0.25,0.25,0.25]; >> y = f...
oltre 5 anni fa | 1 risposta | 0
1
rispostaDomanda
Beamforming for DOA estimation
Hi I want to simulate few beamforming techniques in matlab for DOA estimation and understand the underlying Mathematics. Plea...
oltre 5 anni fa | 1 risposta | 0
1
rispostaDomanda
creating circular cavity for spiral antenna
Hi I am using matlab R2016a I want to use cavityCircular for designing the cavity of a spiral antenna But I am getting t...
oltre 5 anni fa | 1 risposta | 0
1
rispostamaking UCA using spirall antenna
As a second option I designed the spiral antenna using the following command sa = spiralArchimedean('Turns',2, 'I...
oltre 5 anni fa | 0
making UCA using spirall antenna
Thanks I am using the phased array custom antenna design and entering 17 frequencies. for frequency response should I add th...
oltre 5 anni fa | 0
Domanda
making UCA using spirall antenna
I have to modle a receiver that has spiral antennas placed equidistant in a circular array. In phase array tool box I could...
oltre 5 anni fa | 4 risposte | 0
4
risposteDomanda
generate a bandpass signal
I want to generate a bandpass signal .How can it be accomplished in matlab regards
quasi 6 anni fa | 1 risposta | 0
1
rispostaDomanda
how to plot multi variable function
How can i plot this multi variable function t=@(x,y)(x^2-2*x-x*y+2*y^2); regards
quasi 6 anni fa | 2 risposte | 0
2
rispostereading frequency from fft
Than you Youssef It helped me Please guide that if the input is a frequency modulated signal with multiple valid peaks in fft ...
circa 6 anni fa | 0
Domanda
reading frequency from fft
I want to read the frequencies of all peaks of fft the following program is not reading it correctly instead of giving 100 an...
circa 6 anni fa | 2 risposte | 0
2
risposteDomanda
I want to read histogram values
I want to read value of y at x=0 and 1 from the histogram . Please guide me. Here is the histogram: <<https://www.mathworks....
circa 6 anni fa | 1 risposta | 0