Community Profile

photo

Geetla Sindhu

MathWorks

Last seen: Today Attivo dal 2022

I am an EDG Engineer at MathWorks. Any advice or opinions here are my own, and in no way reflect that of MathWorks.

Statistics

All
  • 3 Month Streak
  • Knowledgeable Level 2
  • CUP Challenge Master
  • MATLAB Central Treasure Hunt Finisher
  • Solver
  • First Answer

Visualizza badge

Content Feed

Visto da

Risposto
Wind turbine model block, cp(lambda, beta) function syntax error
Hello Giovanni, I understand that you are getting syntax error using MATLAB function block in Simulink. The cause of this erro...

29 giorni fa | 0

Risposto
Syntax error in Simulink
Hello Nibash, I understand that you are getting syntax error while using MATLAB function block in Simulink. The cause of this ...

29 giorni fa | 0

Risposto
modifying vertices of geopolyshape
Hello Murat, I understand that you are trying to use geopolyshape with geographic coordinates. You can try the following worka...

29 giorni fa | 0

Risposto
Gear shifting scenario to overcome all resistance forces with using switch
Hello Batuhan, I understand that you are using velocity information to change the gears accordingly. You can use the MATLAB Fu...

30 giorni fa | 1

| accettato

Risposto
Copy slides from ppt & paste it as an image in excel sheet.
Hello Himanshu, I understand that you are trying to copy the slide from .ppt file and paste in an excel sheet. You can try the...

30 giorni fa | 0

| accettato

Risposto
Needed RMS for matlab code for a ECG signal
Hello Sachini, I understand that you are trying to estimate the RMS values of a signal for every 1 second interval. Since the ...

circa un mese fa | 0

| accettato

Risposto
How to use 'for' loop in Erlang B formula
Hello, I understand that you are trying to use Erlang B equation for different number of channels. The approach for this can b...

circa un mese fa | 0

Risposto
how to do FFT analysis in MATLAB 2021a ? i am having an issue in getting THD from the scope can any one suggest me a idea.. it will
Hello Dhanesh, I understand that you are not able to view the signal and get THD of that signal using Powergui FFT Analysis too...

circa un mese fa | 0

Risposto
How TI c2000 ePWM block can be configured?
Hello Abirami, I understand that you are trying to achieve desired switching frequency using TI C2000 ePWM block in Simulink. ...

circa un mese fa | 0

Risposto
error while designing electric vehicle in Simulink
Hello Nimil, In order to solve the issue, you have to add “Electrical Reference” block from the Simscape Library as there are c...

circa un mese fa | 0

Risolto


Calculate Inner Product
Given two input matrices, |x| and |y|, check if their inner dimensions match. * If they match, create an output variable |z|...

2 mesi fa

Risolto


Find MPG of Lightest Cars
The file |cars.mat| contains a table named |cars| with variables |Model|, |MPG|, |Horsepower|, |Weight|, and |Acceleration| for ...

2 mesi fa

Risolto


Find the Best Hotels
Given three input variables: * |hotels| - a list of hotel names * |ratings| - their ratings in a city * |cutoff| - the rat...

2 mesi fa

Risolto


Crop an Image
A grayscale image is represented as a matrix in MATLAB. Each matrix element represents a pixel in the image. An element value re...

2 mesi fa

Risolto


Calculate BMI
Given a matrix |hw| (height and weight) with two columns, calculate BMI using these formulas: * 1 kilogram = 2.2 pounds * 1 ...

2 mesi fa

Risposto
Why thd() function captures incorrect harmonics?
Hello Ying Wu, I understand that you are trying to calculate THD of a signal using three approaches. It would be helpful if y...

2 mesi fa | 0

Risposto
Receiving error when code is correct on matlab onramp Project - Stellar Motion I task 4?
Hello Alysia, I am not able to reproduce the issue on my end and from your screenshot, it does look like you did it correctly. ...

2 mesi fa | 0

Risposto
I need to plot a phase response using freqz function. Can you please help with it.
Hello Gerald, I understand that you are trying to plot the phase of the frequency response of the system using “freqz” command...

2 mesi fa | 0

Risposto
connecting battery to inverter
Hello Layth, In order to solve the issue, you can connect the three-phase inverter to the battery as shown in the image below. ...

2 mesi fa | 0

| accettato

Risolto


Calculate a Damped Sinusoid
The equation of a damped sinusoid can be written as |y = A.ⅇ^(-λt)*cos(2πft)| where |A|, |λ|, and |f| ...

2 mesi fa

Risolto


Solve a System of Linear Equations
Example: If a system of linear equations in x₁ and x₂ is: 2x₁ + x₂ = 2 x₁ - 4 x₂ = 3 Then the coefficient matrix (A) is: 2 ...

2 mesi fa

Risolto


Find the Oldest Person in a Room
Given two input vectors: * |name| - user last names * |age| - corresponding age of the person Return the name of the ol...

2 mesi fa

Risolto


Convert from Fahrenheit to Celsius
Given an input vector |F| containing temperature values in Fahrenheit, return an output vector |C| that contains the values in C...

2 mesi fa

Risolto


Calculate Amount of Cake Frosting
Given two input variables r and h, which stand for the radius and height of a cake, calculate the surface area of the cake you n...

2 mesi fa

Risolto


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

2 mesi fa

Risposto
how to model a pv/pcm system in matlab/simulink
Hello Thabo, One option to consider is using the two-phase fluid domain in Simscape to model the evaporation and condensation o...

2 mesi fa | 0

Risposto
Can I use "To File" block inside Matlab Function in the form of a command?
Hello Ehtisham, I understand that you are using a MATLAB function and wanted to save the data to a .mat file but without using ...

2 mesi fa | 0

Risposto
How can I add a PS control port to a Spice imported Simscape block?
Hello Niklas, I understand that you are trying to connect Simscape-GaN-Transistor-block with a MATLAB function or any Simulink ...

2 mesi fa | 0

Risposto
How to enable block content preview in Simulink?
Hello Nathan, I understand that when you are adding an icon image to the Simulink block and removing it, the block content prev...

2 mesi fa | 1

| accettato

Risposto
An error occurred while running the simulation and the simulation was terminated .
Hello Aravind, In order to solve the issue, you have to add “Electrical Reference” block from the Simscape Library. You can fin...

2 mesi fa | 1

Carica altro