Statistica
29 Domande
0 Risposte
RANK
279.034
of 300.771
REPUTAZIONE
0
CONTRIBUTI
29 Domande
0 Risposte
ACCETTAZIONE DELLE RISPOSTE
68.97%
VOTI RICEVUTI
0
RANK
of 170.969
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Domanda
Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?
this is the simulink model where the buck-boost controller is connected to the gate ports of each switch to power up the conve...
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi. How do I maintain the square wave output of the 1-D?
the blue triangular waveform is the waveform of 1-D, and the red square wave is the D
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi. In Simulink modeling, what can we do to ensure that the switching waveforms of the duty cycle and 1-duty cycle are not in phase?
q1 is the duty cycle (D), and q3 is the 1-duty cycle (1-D)
circa 2 anni fa | 2 risposte | 0
2
risposteDomanda
Hello. Could someone please suggest other components or blocks I can use to avoid using the step input block for the duty cycle?
Because I need the amplitude to reach 1.8V, and I only get 1V with the step input.
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Could someone please assist me? My code for the buck-boost converter controller isn't working properly when I run it.
this is the Simulink model
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hello, if you have a moment, I could use your help in resolving this error.
circa 2 anni fa | 2 risposte | 0
2
risposteDomanda
Greetings, if you have a moment, I could use your help in resolving this error.
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hello, how do I feed the output of the input selector to the buck-boost converter using Simulink modeling?
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hey there, I need some help with this error. Would anyone be willing to provide guidance?
How do I reduce the fixed step size or tighten the error tolerances?
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi there, I'm encountering an issue and would appreciate your guidance in resolving it.
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Greetings! I'm looking for assistance in understanding what's causing the problem in my code.
this is the MATLAB code: function y = determineMode(teg, pv, pzt, ~, D, ~, ~, ~, ~) % Inputs: % teg: Voltage from T...
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hey there, I need some help with this error. Your guidance would be valuable.
circa 2 anni fa | 0 risposte | 0
0
risposteDomanda
Hi, would someone be willing to assist me in resolving this error
circa 2 anni fa | 1 risposta | 0
1
rispostaDomanda
hey, could somebody please help me understand and resolve this error?
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
hello, can somebody help me figure out how to improve this Simulink model so that it has four output ports instead of a single output port?
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
hi, is the simulink model shown below possible?
we feed 4 input switches into a stateflow
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
Hello, can someone please help me understand this error?
I'm particularly confused about the part which says '... and the phase delay parameters of this block need to be integer multi...
oltre 2 anni fa | 1 risposta | 0
1
risposta1
rispostaDomanda
Hello, could someone kindly assist me in resolving this error?
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Can someone please help me learn how to make automatic switching based on available voltage sources to power up a three-input buck-boost converter?
An example of this operation would be: TEG: 0.3 - 0.4V PV: 0.4 - 1.2V PZT: 1.2 - 2V Ideal Output: 1.8V If the available...
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi. Could someone please assist me in resolving this issue?
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Could someone please tell me which components are missing for this circuit to automatically and appropriately select inputs when dealing with multiple inputs?
3 inputs
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi! I need some help. I'm confused as to why this selection mode circuit I modified won't work properly with three inputs.
1st input: 0.3 - 0.4V 2nd input: 0.4 - 1.2V 3rd input: 1.2 - 2V
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hello! Could someone kindly assist me in comprehending the purpose and operation of the system shown below?
This is one of the subsystems of an input selector circuit.
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
Hi! Could someone please provide me with an idea of how to model a selector for multiple inputs using Simulink? Thank you.
Input sources: Thermoelectric Generator(TEG), Photovoltaic(PV), and Piezoelectric(PZT)
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
What should be the inductor initial current and capacitor initial voltage with an input range of 0.02-0.16V
for a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...
oltre 2 anni fa | 1 risposta | 0
1
rispostaDomanda
What should be the initial value of the inductor and capacitor with an input range of 0.02-0.16V
For a two MOS switch two diodes buck-boost converter with an input of 0.02V, resistor load of 2,142,857.143 Ω, inductance of 1 m...
oltre 2 anni fa | 0 risposte | 0
