Risposto
How to change a single value on a different vector cell each time? (simulink)
Picking apart vectors can be a little tough in Simulink with only blocks. Fortunately, Simulink is built on MATLAB and that giv...

oltre 11 anni fa | 0

| accettato

Risposto
Engine Speed controller Simulink
The entire subsystem represents a calculation of the mass flow rate. You can find the equation on the <http://www.mathworks.com...

oltre 11 anni fa | 1

Risposto
how could i solve this ode system in simulink?
See the blog post about <http://blogs.mathworks.com/seth/2008/05/23/how-to-draw-odes-in-simulink/ building odes in simulink>. ...

oltre 11 anni fa | 0

Risposto
Simulink model comparison with R2012b
Try doing the process on <http://www.mathworks.com/help/simulink/ug/try-simulink-project-tools-with-the-airframe-project.html th...

oltre 11 anni fa | 0

| accettato

Risposto
SIM command clears workspace
This SIM command should not clear your workspace, you should not have to workaround that. Check your <http://www.mathworks....

oltre 11 anni fa | 0

Risposto
Easy Simulink Questions (new user)
1. You cannot convert between Block Diagram and MATLAB-Code (.m file) 2) PSI (being cvariable) would be connected to a gain b...

oltre 11 anni fa | 1

| accettato

Risposto
Checking values with Simulink
You could use something like this <http://www.mathworks.com/matlabcentral/fileexchange/5761-reset-clock reset timer> on the File...

oltre 11 anni fa | 0

| accettato

Risposto
Insert Simulation from Simulink to GUI
At about 35 seconds into the video you see this tool pop up in the GUI. This shows that he is using a virtual reality animation...

oltre 11 anni fa | 0

Risposto
How can I read a .mdb file from MATLAB?
You can try using the GUI first to make sure your commands are working as intended then use the Generate MATLAB file option in t...

oltre 11 anni fa | 0

Risposto
Run scripts in parallel on multiple workers (distributed job)
It sounds like there are multiple simulations in each script. So the number of simulations would be the sum of the three and yo...

oltre 11 anni fa | 0

Risposto
Integration of Matlab Fuzzy .FIS into Java
Depending on how you want to deploy this there are a few options. If you are ok with installing the <http://www.mathworks.com/p...

oltre 11 anni fa | 0

Risposto
creating a simple simulation
You can try using a <http://www.mathworks.com/help/physmod/powersys/ref/controlledvoltagesource.html controlled voltage source> ...

oltre 11 anni fa | 0

Risposto
Simulink conditional pass-through
You can perform <http://blogs.mathworks.com/seth/2012/04/09/conditional-execution/ conditional execution> with the merge block s...

quasi 12 anni fa | 1

| accettato

Risposto
Retrieving data from structures
Assuming your structure is like: periodicTable.Helium periodicTable.Carbon etc... names = fieldnames(myTable); inG...

quasi 12 anni fa | 0

Risposto
how can I change series of data into time series data
You can use the <http://www.mathworks.com/help/matlab/ref/datestr.html datestr> function to convert between a numerical represen...

quasi 12 anni fa | 0

| accettato

Risposto
How can I implement coder.ceval in Simulink?
From the error and based on the line you use to generate the code, it looks like it can't find the libraries you utilized, math....

quasi 12 anni fa | 0

Risposto
averaging over a timeseries
You could try utilizing the <http://www.mathworks.com/help/matlab/ref/tstool.html tstool> in MATLAB and see if that can ease thi...

quasi 12 anni fa | 0

Risposto
Optimization based on inputs and outputs (for online optimization)
I think any response is highly dependent on the system, so keep in mind it is difficult, even when described, to determine how I...

quasi 12 anni fa | 1

| accettato

Risposto
Is there any other way to realize Simulink Block of "Tapped Delay" function?
You can try changing some of the optimizations in the configuration parameters to see if that changes the generated code at all....

quasi 12 anni fa | 1

Risposto
Joint saturation in simmechanics second generation
You can use an <http://www.mathworks.com/help/physmod/sm/ref/angleconstraint.html angle constraint> to limit the motion of a rev...

quasi 12 anni fa | 1

Risposto
Xpc target data logging at different rate
Eventually I would suspect the system will run out of memory for one reason or another. However, you can use a file scope to lo...

quasi 12 anni fa | 0

Risposto
Using parallel computing WITHIN a Simulink simulation
You cannot use parallel computing for this operation. Can I ask why you are doing this? Although there may be a perfectly vali...

quasi 12 anni fa | 1

Risposto
Solving for multiple variables
You have 1 equation and 4 unknowns. Assuming you have at least 4 sets of X/Y values you can split this into 4 equations with 4 ...

quasi 12 anni fa | 0

Risposto
Simulink model very slow when integrates
It sounds like the model is behaving as expected with a variable step ODE solver. Essentially it will take bigger (faster) step...

quasi 12 anni fa | 0

Risolto

Determine whether a vector is monotonically increasing
Return true if the elements of the input vector increase monotonically (i.e. each element is larger than the previous). Return f...

quasi 12 anni fa

Risposto
How can I autotune some parameters based on a Simulink model?
Simulink already has a <http://www.mathworks.com/products/simcontrol/examples.html?file=/products/demos/shipping/slcontrol/scdsp...

quasi 12 anni fa | 0

Risposto
How can I modify the manipulated variable properties in a MPC block in Simulink?
I don't know if I would normally use a MPC control for a bang-bang (on/off) control scheme, but then again I'm not really that f...

quasi 12 anni fa | 0

Risposto
MBD: Blocks or C-code ?
It would be tough to say exactly what is best given the unknowns in this case. However, in general, using blocks should be the ...

quasi 12 anni fa | 0

Risposto
Generating Biased Random Number
I'm no statistician, so I bet there's a better way but you can try this without stats toolbox: Setup an index for each number...

quasi 12 anni fa | 0

Risposto
VideoReader: audio from avi
Have you tried: [y,Fs] = audioread('myFile.avi'); If this doesn't work you should get the output from info = mm...

quasi 12 anni fa | 0