Vijith Natarajan
Pricol technologies Limited
Followers: 0 Following: 0
Statistica
13 Domande
0 Risposte
RANK
212.376
of 300.791
REPUTAZIONE
0
CONTRIBUTI
13 Domande
0 Risposte
ACCETTAZIONE DELLE RISPOSTE
53.85%
VOTI RICEVUTI
0
RANK
160.598
of 171.108
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Domanda
how to do PIL simuilation, if target support package of a micrcontroller does not support PIL?
Hi, I am working on PIL implementation of PIC32mx795f512L microcontroller. I downloaded target support package from this l...
circa 12 anni fa | 1 risposta | 0
1
rispostaDomanda
Generated code is not conforming with Simulation?
Hi, I am using a interpolation prelookup table in my model. from my stateflow chart i am calling the interpolation block a...
quasi 13 anni fa | 0 risposte | 0
0
risposteDomanda
Is it possible to give a hex input to stateflow chart from simulink?
Hi, i want to give hex input from simulink to a stateflow chart which does some shifting and the gives the shifted output t...
quasi 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Problem in generating code for a simple model
Hi, I did a small state flow model, which should produce a output 1 when the input is 0 and produce ouput 0 when the inpu...
quasi 13 anni fa | 1 risposta | 0
1
rispostaDomanda
what is the difference between simulink control design and control system toolbox?
Hi, while going through simulink control design i came across a thing that we can linearize non linear models , 1. Is th...
circa 13 anni fa | 2 risposte | 0
2
risposteDomanda
Can we integrate Fijitsu softune IDE with embedded coder?
Hi, Can we integrate Fijitsu softune IDE with embedded coder for generating controller specific C code?
circa 13 anni fa | 0 risposte | 0
0
risposteDomanda
Is data acquistion toolbox meant to work with only sensors and actuators?
Hi, i have just started learning data acquisition toolbox. when i go through the documentation i could see there it is ment...
circa 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Why i can't connect with an instrument using ivi com driver?
Hi, I created and device object using both drivers(ivi c and ivi com). when i try to connect the instrument using ivi c dr...
circa 13 anni fa | 1 risposta | 0
1
rispostaDomanda
can we create multiple device objects in instrument control toolbox?
1.can we create multiple device objects in instrument control toolbox and make them communicate parallely without disturbing eac...
circa 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Need help to find the error in the code below
Hi i tried to acquire the waveform from the agilent scope to matlab using tmtool of instrument control toolbox. when i execute ...
circa 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Cannot connect the AGILENT oscilloscope after creation of the device object
i have created an interface object and when i click connect it has connected and i could be able to send commands and read from ...
circa 13 anni fa | 0 risposte | 0
0
risposteDomanda
Can any one tell me that whether VISA is a software architecture or an interface standard?
when i was reading tutorials in Instrument control toolbox, i came cross VISA manytimes, some explaining it as an interface and ...
circa 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Can we connect a Agilent Oscilloscope with MATLAB workspace without any external hardwares???
Hi, I am trying to connect and capture waveforms from oscilloscope (Agilent MSO X2024A) through instrument control tool b...
circa 13 anni fa | 1 risposta | 0
