Statistica
RANK
128.357
of 294.407
REPUTAZIONE
0
CONTRIBUTI
18 Domande
1 Risposta
ACCETTAZIONE DELLE RISPOSTE
22.22%
VOTI RICEVUTI
0
RANK
of 151.611
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Domanda
Nested enablement subsystems with two childs
I see below link that for nested subsystems whose Enable blocks have different parameter settings, the settings for the child su...
12 mesi fa | 1 risposta | 0
1
rispostaDomanda
Simulink models comparison issue
I'm comparing two simulink models and in the report i'm getting the following difference. I don't really figure out what that di...
oltre 2 anni fa | 0 risposte | 0
0
risposteExport Structure to csv file
Hi, I tried to used the same method to convert my struct mat file (attached) but failed. Any help is appreciated.
oltre 2 anni fa | 0
Domanda
Convert CANFD messages to standard CAN messages
I have a DBC file which contains 10 CANFD messages each contains 64 bytes of signals. I need to create a new DBC in which each o...
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
Dynamic memory allocation problem
I have a simulink model in which I need to use dynamic memory allocation ro run the model. For some reason, in the config. dial...
oltre 2 anni fa | 0 risposte | 0
0
risposteDomanda
How to handle varying mass value in Lightweight Airplane Design
I am considering the aircraft model and compensators used in the Lightweight Airplane Design but with a varying mass value. 1...
oltre 3 anni fa | 0 risposte | 0
0
risposteDomanda
How to change only the LineStyle of the top curve?
I'm trying the following code (Mathworks example) but I only want the LineStyle of top curves to be as specified (like the attac...
quasi 5 anni fa | 1 risposta | 0
1
rispostaDomanda
Matlab considers different two equal numbers!
I calculated a matrix (attached). In the 11th row, matlab considers the 3rd column, i.e., entry (11, 3) as the maximum entry of ...
quasi 5 anni fa | 2 risposte | 0
2
risposteDomanda
Limit on the change rate of the variable in fmincon function
Hi, In fmincon function, how can I put lower and upper bounds on the change rate of a signal, i.e., ? Thanks
quasi 5 anni fa | 2 risposte | 0
2
risposteDomanda
Solve symbolic Sylvester-like equation
I'm looking for a way to solve a symbolic Sylvester-like equation in MATLAB or MAPLE (or any other available tool). In particula...
oltre 5 anni fa | 1 risposta | 0
1
rispostaDomanda
How to resolve "Dot indexing is not supported for variables of this type." error?
Hi, I'm running the attached files as follows, Run the following MATLAB command and select the Microsoft Visual C++ 2015 Profe...
oltre 5 anni fa | 0 risposte | 0
0
risposteDomanda
How to freeze a particular column of matrix in a for loop?
Hi, I am updating a matrix in a for loop. I want to freeze a particular column of this matrix, say column j, and update the r...
oltre 6 anni fa | 0 risposte | 0
0
risposteDomanda
Error using GA in MATLAB for nonlinear constrained optimization
I am using GA in MATLAB to minimize a convex function. I am getting the following error, Error using constrValidate (line 5...
oltre 6 anni fa | 2 risposte | 0
2
risposteDomanda
Need help for a nonlinear constraint optimization problem
Dear all, I am going to solve the following nonlinear constraint optimization problem using MATLAB. I was wondering if you co...
oltre 6 anni fa | 0 risposte | 0
0
risposteDomanda
read only the numerical value of a file
Hi, I have a file which is attached. I just want to read the number in it and store it in a variable. Thanks for your help.
oltre 6 anni fa | 1 risposta | 0
1
rispostaDomanda
How to append "Sampled Gaussian Noise" in Signal Builder Block "from m-file"?
Hi, How can I tell the Simulink to generate "Sampled Gaussian Noise" signal in the Signal Builder block from command window? (I...
oltre 7 anni fa | 0 risposte | 0
0
risposteDomanda
How to change the signal in Signal Builder Block from m-file?
Hi, I am using "Signal Builder" block in a Simulink model and I am going to run it many times (using a for loop in a m-file). ...
oltre 7 anni fa | 1 risposta | 0
1
rispostaDomanda
identifying continuous-time and discrete-time models using ident toolbox
Hello, I have some questions regarding system identification toolbox. I am running a simulink model and collect data with ...
oltre 7 anni fa | 1 risposta | 0
1
rispostaDomanda
Phase margin with several gain crossover frequencies
Dear all, when in a system, we have several gain crossover frequencies, naturally we'll have several phase margins. But margin...
oltre 9 anni fa | 0 risposte | 0