photo

Yusuf Selim KARATAS


Last seen: quasi 3 anni fa |  Attivo dal 2019

Followers: 0   Following: 0

Statistica

  • Thankful Level 1
  • Knowledgeable Level 1
  • First Answer
  • First Review

Visualizza badge

Feeds

Visto da

Domanda


SIMSCAPE Parameters from WorkSpcae
Dear All, I have a simscape model that has some parameters like SOC_points, T_points and C points. I enter cell_SOCpoints, cell...

oltre 3 anni fa | 0 risposte | 0

0

risposte

Domanda


Version Control for slx Files
Dear All, We are currently using Version Control systems in our project on Matlab. Our project has .slx files and since .slx ...

oltre 3 anni fa | 0 risposte | 0

0

risposte

Domanda


PROCESSOR IN THE LOOP - DATA PAYLOAD
Dear All, I am working on NXP S32K144 with MBD tools. What I am trying to is implementing Processor in the Loop Simulation with...

quasi 4 anni fa | 0 risposte | 0

0

risposte

Domanda


Matlab Simulink RepMat Execution Time
Dear All, I need a significant help. I have a Simulink model that has a subsystem that takes a matris [3x1] and makes it [3x...

quasi 4 anni fa | 1 risposta | 0

1

risposta

Domanda


SIMULINK PROFILER - NUMBER OF CALL
Hello everyone, I am trying to use Profiler function for SIL of one of the models that I have. I was checking number of call ...

circa 4 anni fa | 0 risposte | 0

0

risposte

Domanda


Design verifier Unsupported data pointer
Dear All, We are trying to use Simulink Design Verifier in one of our model to detect PIL problem(run time failure). But we g...

circa 4 anni fa | 1 risposta | 0

1

risposta

Domanda


PIL Communication Timeout for MPC57xx
Dear All, I am trying to use external mode for C2000 and PIL for MPC57xx. for C2000 even sample project model gives commun...

oltre 4 anni fa | 0 risposte | 0

0

risposte

Domanda


SIMULINK WHILE LOOP with Estimator
Dear All, I am trying to build a while loop that tries to estimate future values. Block diagram is as below. Main Code ...

oltre 4 anni fa | 0 risposte | 0

0

risposte

Domanda


C28x Memory Operations
Dear All, I am trying to add memory operations one of my complex model. But before directly implementing to complex one , I j...

oltre 4 anni fa | 0 risposte | 0

0

risposte

Domanda


C2000 CAN RX
Dear All, I am using Simulink to build a model to receive CAN messages. You can see diagram below. I am getting "error: express...

oltre 4 anni fa | 1 risposta | 0

1

risposta

Domanda


C2000 timer interrupt for 1 second
Dear All, I want to set 1 second timer in C2000 and output an analog signal. How can I do that? Can you help me? I have also ...

oltre 4 anni fa | 0 risposte | 0

0

risposte

Domanda


C2000 SCI BYTES IN ONE FRAME
Dear All, I am trying to use C2000 SCI function. I need to send more than 1 BYTE in a frame to communicate with BQ76PL455EVM....

quasi 5 anni fa | 0 risposte | 0

0

risposte

Domanda


F28379D READING VALUES FROM GPIO INPUT AND SCI RCV
Hello, I want to see whether a digital input is HIGH or LOW but scope and display always show 0 despite of changing voltage l...

quasi 5 anni fa | 0 risposte | 0

0

risposte

Domanda


Data Store Memory to Global Workspace
Hello, I am using a function that reads some values from a data storage memeory and writes back to data storage memory. What ...

quasi 5 anni fa | 1 risposta | 0

1

risposta

Domanda


28379D GPIO INPUT
Hi, I want to use GPIO input and want to see incoming signal on my computer but incoming signal always seem as 0 Zero. How ca...

quasi 5 anni fa | 1 risposta | 0

1

risposta

Risposto
C2000 F28379d SCIB
Hello Venkatesh, To be clear, you mean that you have tried and used succesfully SCI B on my model, am I right? Thanks.

quasi 5 anni fa | 0

Domanda


C2000 SCI B and SCI C
Hi everyone, I am using 28379d LaunchPad and could not get any signal on SCI B and SCI C. I have attached model. Can you tell...

quasi 5 anni fa | 0 risposte | 0

0

risposte

Risposto
C2000 F28379d SCIB
Is there anyone that can help me on this issue ?

quasi 5 anni fa | 0

Risposto
Error in Code build for C2000 Piccolo F28027
I dont know the source of the problem. But I have learned that sometimes you need to change clock frequency on these boards. Kee...

quasi 5 anni fa | 0

Domanda


C2000 F28379d SCIB
Hello, I need to use SCIB port of the F28379d on MATLAB Simulink. I assign some pins for SCIB communication and SCIC communic...

quasi 5 anni fa | 3 risposte | 0

3

risposte

Domanda


SIMSCAPE INPUT FOR SOURCE CODE
Hello eveyone, I want to use a generate a temperature dependent voltage source in simscape by using dc voltage source. Temper...

quasi 5 anni fa | 1 risposta | 0

1

risposta