CAN Transmit
Transmit message to CAN network
Add-On Required: This feature requires the Simulink Support Package for Arduino Hardware add-on.
Libraries:
Simulink Support Package for Arduino Hardware /
Common
Description
The CAN Transmit block transmits message to a Controller Area Network (CAN) network by using the CAN shield. The CAN shield is connected to the Serial Peripheral Interface (SPI) pins on the hardware.
Click View pin map to open the Arduino Pin Mapping table.
To know how to assign pins for the block, see Pin Mapping for Arduino Timer Independent Blocks.
Specify the message type and its properties using the block parameters dialog box. Specify the CAN properties of the model in the Configuration Parameters dialog box.
This block supports only MCP2515-based CAN shields.
If you simulate a model that contains the CAN Transmit block without connecting the hardware, the block does nothing. For more information, see Block Produces Zeros or Does Nothing in Simulation.
Ports
Input
Port1 — Message data
vector | scalar
The block accepts messages in Raw data
and
CAN Msg
formats.
Raw data
– To accept the message as auint8
vector array, set Data is input as asRaw data
.CAN Msg
– To accept the message in CAN message format, set Data is input as asCAN Msg
. You can create your messages or you can upload a CAN database file. For more information, see Data is input as.
Data Types: uint8
| CAN Msg
Output
Port1 — Status of data transmission
scalar
Output port to display status of data transmission. For more information, see Output Status.
Dependencies
This port appears only when you select the Output Status parameter.
Parameters
Data is input as — Data input type
Raw data
(default) | CAN Msg
Select the type of the message at the input port.
Raw data
– To accept the message as auint8
vector array, set Data is input as asRaw data
.CAN Msg
– To accept the message in CAN message format, set Data is input as asCAN Msg
and then perform these steps:Add a CAN Pack (Vehicle Network Toolbox) block from the Vehicle Network Toolbox™ to your model.
Connect the output of CAN Pack block to the input port of the CAN Transmit block.
Using the options in the Data is input as list of the CAN Pack block, specify if you want to create your messages or you want to upload a CAN database file. If you choose to upload a CAN database file, the CAN Pack inherits the message properties from the uploaded file.
Note
To use CAN Pack block, you must have a Vehicle Network Toolbox license.
Output Status — Status of data transmission
off
(default) | on
When you select the Output Status parameter, the
block configures an output port. The port outputs the status of the data
transmission as a uint8
integer. Each bit in the integer
corresponds to the type of error occurred during data transmission. An
output of 0
indicates successful transmission.
Wait until data sent — Wait until the data is sent
off
(default) | on
on
— When you select this parameter, the block operates in the Blocking mode. If the message received in the previous time step is sent, the block accepts message from the input port. If the send operation is in progress, the block waits for the time specified in the Time out in seconds parameter, and then it accepts message from the input port.A task overrun occurs if the target hardware is still waiting for the requested message to be sent when the next send operation is scheduled to begin. To fix overruns:
Increase the sample time of input message.
Reduce the length of message at the input port.
off
— When you clear this parameter, the block operates in the Non-blocking mode. If the transmission of the message received in the previous time step is still in progress, the message at the input port at the given time step is dropped.
Time out in seconds — Waiting time for sending message
1 (default) | integer
Specify the wait time for sending the message. After the specified time, the block times out.
Dependencies
This parameter appears only when you select the Wait until data sent parameter.
Message ID — Message identifier
100 (default) | numeric identifier of length 11 or 29 bits
Message identifier, which is 11 bits long for the standard frame or 29
bits long for the extended frame, specified in decimal, binary, or hex. For
binary and hex formats, use bin2dec(' ')
and
hex2dec(' ')
, respectively, to convert the entry. The
message identifier is coded into a message that is sent to the CAN
bus.
Dependencies
This parameter appears only when you select Data is input
as as Raw data
. For
CAN Msg
, Message ID
is inherited from the identifier specified in the CAN
Pack block.
Identifier Type — Message identifier type
Standard (11-bit
identifier)
(default) | Extended (29-bit identifier)
The type of message identifier.
Dependencies
This parameter appears only when you select Data is input
as as Raw data
. For
CAN Msg
, Identifier
Type is inherited from the type specified in the CAN Pack
block.
Message Length — Length of message
8 (default) | positive integer less than or equal to 8
The length of the message, in bytes.
Dependencies
This parameter appears only when you select Data is input
as as Raw data
. For
CAN Msg
, Message
Length is inherited from the length of the CAN
Pack block.
Request Remote Frame — Enable remote message
off
(default) | on
When you select the Request Remote Frame parameter, the remote frame of the message is set to 1 indicating that the block is requesting the transmission of a specific identifier.
Dependencies
This parameter appears only when you select Data is input
as as Raw data
. For
CAN Msg
, the Request Remote
Frame is inherited from the request specified in the
CAN Pack block.
Version History
Introduced in R2019b
Comando MATLAB
Hai fatto clic su un collegamento che corrisponde a questo comando MATLAB:
Esegui il comando inserendolo nella finestra di comando MATLAB. I browser web non supportano i comandi MATLAB.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)