What is the difference between "phased.LinearFMWaveform" and "phased.FMCWWaveform"
5 visualizzazioni (ultimi 30 giorni)
Mostra commenti meno recenti
1. What is the difference between "phased.LinearFMWaveform" and "phased.FMCWWaveform" in Phased Array System Toolbox except for that Triangle waveform generation is possible in P"phased.LinearFMWaveform" function.
2. My other concern is I want to sweep bandwidth of 10Mhz from start frequency of 10 MHz and End Frequency 20MHz. How can i do that in "phased.LinearFMWaveform" function.
3. When i dechirp the received signal from transmitted signal of saw-tooth waveform, i should get 2 beat frequencies (according to "New ideas in FM Radar by H. D. Griffiths"). but i get only 1 beat frequency, why?
0 Commenti
Risposta accettata
Honglei Chen
il 27 Dic 2012
Hi Ali,
LinearFMWaveform is a pulse waveform, meaning that in general the system only transmit a very short period of time during one cycle and uses the rest of cycle to receive. On the other hand, FMCWWaveform is a continuous waveform, so the system transmits and receives at the same time and the duty cycle for the waveform is always 1.
Currently you cannot specify the starting and ending frequencies in LinearFMWaveform. However, depending on the system setup, you may still be able to simulate your case. For example, if your system's center frequency is 15 MHz, then your situation is just a symmetric sweeping over a 10MHz range.
I don't have that particular paper handy so I cannot comment much on your third question without seeing some code snippet.
HTH
4 Commenti
Più risposte (1)
Nadir HEFHAF
il 10 Set 2017
Modificato: Honglei Chen
il 11 Set 2017
i have problem also in this program
close all
clc
clear all
L = 50;
N = 4;
rxULA = phased.ULA('Element',phased.OmnidirectionalMicrophoneElement,...
'NumElements',N);
rxpos1 = [0;0;0];
rxvel1 = [0;0;0];
rxax1 = azelaxes(90,0);
rxpos2 = [L;0;0];
rxvel2 = [0;0;0];
rxax2 = rxax1;
srcpos = [30;100;0];
srcvel = [0;0;0];
srcax = azelaxes(-90,0);
srcULA = phased.OmnidirectionalMicrophoneElement;
fc = 300e3; % 300 kHz
c = 1500; % 1500 m/s
dmax = 150; % 150 m
pri = (2*dmax)/c;
prf = 1/pri;
bw = 100.0e3; % 100 kHz
fs = 2*bw;
waveform = phased.LinearFMWaveform('SampleRate',fs,'SweepBandwidth',bw,...
'PRF',prf,'PulseWidth',pri/10);
signal = waveform();
nfft = 128;
radiator = phased.WidebandRadiator('Sensor',srcULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
collector1 = phased.WidebandCollector('Sensor',rxULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
collector2 = phased.WidebandCollector('Sensor',rxULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
channel1 = phased.WidebandFreeSpace('PropagationSpeed',c,...
'SampleRate',fs,'OperatingFrequency',fc,'NumSubbands',nfft);
channel2 = phased.WidebandFreeSpace('PropagationSpeed',c,...
'SampleRate',fs,'OperatingFrequency',fc,'NumSubbands',nfft);
[~,ang1t] = rangeangle(rxpos1,srcpos,srcax);
[~,ang2t] = rangeangle(rxpos2,srcpos,srcax);
sigt = radiator(signal,[ang1t ang2t]);
sigp1 = channel1(sigt(:,1),srcpos,rxpos1,srcvel,rxvel1);
sigp2 = channel2(sigt(:,2),srcpos,rxpos2,srcvel,rxvel2);
[~,ang1r] = rangeangle(srcpos,rxpos1,rxax1);
[~,ang2r] = rangeangle(srcpos,rxpos2,rxax2);
sigr1 = collector1(sigp1,ang1r);
sigr2 = collector2(sigp2,ang2r);
doa1 = phased.GCCEstimator('SensorArray',rxULA,'SampleRate',fs,...
'PropagationSpeed',c);
doa2 = phased.GCCEstimator('SensorArray',rxULA,'SampleRate',fs,...
'PropagationSpeed',c);
angest1 = doa1(sigr1);
angest2 = doa2(sigr2);
yest = L/(abs(tand(angest1)) + abs(tand(angest2)));
xest = yest*abs(tand(angest1));
zest = 0;
srcpos_est = [xest;yest;zest]
the problem is
Array formation and parentheses-style indexing with objects of class 'phased.LinearFMWaveform' is not allowed. Use objects of class 'phased.LinearFMWaveform' only as scalars or use a cell array.
Error in program11 (line 27) signal = waveform();
3 Commenti
Harwanto Zidqi Putro
il 12 Ago 2020
Modificato: Harwanto Zidqi Putro
il 12 Ago 2020
I have version 2016a, and its error with same problem
PATRICK UWIGIZE
il 30 Dic 2021
Modificato: PATRICK UWIGIZE
il 30 Dic 2021
Upgrade you MATLAB to a newer version
Vedere anche
Categorie
Radar
Phased Array System Toolbox
Phased Array Design and Analysis
Antennas, Microphones, and Sonar Transducers
Mostra altro
Scopri di più su Linear Prediction in Help Center e File Exchange
Prodotti
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!