photo

Ardeal Liang


Attivo dal 2018

Followers: 0   Following: 0

Statistica

  • Thankful Level 2
  • Thankful Level 1

Visualizza badge

Feeds

Visto da

Domanda


Recevied signal from ARM is not correct
Hi, I have zedboard and AD9364. I am trying to reproduce the Matlab example in ARM in C code: Receive Tone Signal Using Ana...

circa 6 anni fa | 0 risposte | 0

0

risposte

Domanda


Set the source of transmitter to be DDS on zedboard and AD3964
Hi, I have the boards: AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard I am going to try the experiment of Matlab in C ...

circa 6 anni fa | 0 risposte | 0

0

risposte

Domanda


The specified superclass 'comm.internal.SDRTxZynqFMC234Base' contains a parse error, cannot be found on MATLAB's search path, or is shadowed by another file with the same name
Hi Paul, I am trying to package the example code as an individual app via Matlab menu: APPS-->APPLICATION DEPLOYMENT --> A...

circa 6 anni fa | 0 risposte | 0

0

risposte

Domanda


How to control GPIO of ARM on Zedboard
Hi Paul, I would like to control the GPIO of ARM on my Zedboard. I would like to set one/some GPIO to be 1 or 0. Which ...

circa 6 anni fa | 1 risposta | 0

1

risposta

Risposto
Chang center frequency quickly
Hi Paul, Thanks for your answer! Here are the steps(pseudo-code) of the exeriment I wang to do: for rf_scan = 1:10 ...

circa 6 anni fa | 0

Risposto
Chang center frequency quickly
Hi Paul, At present, the example runs on Matlab, and send commands to ARM to talk to AD9364 by RJ45 interface. So, the exa...

circa 6 anni fa | 0

| accettato

Domanda


Chang center frequency quickly
Hi Paul, I would like to change center frequency quickly. If I change it and then restart the object in Matlab, it runs too ...

circa 6 anni fa | 3 risposte | 0

3

risposte

Domanda


The received signal from sdrrx keeps unchanged even if I connect or disconnect the loopback cable to trainsmitter port TxA and receiver port RxA
Hi, I am trying to reproduce this example: Receive Tone Signal Using Analog Devices AD9361/AD9364from: https://ww2.mathwor...

circa 6 anni fa | 1 risposta | 0

1

risposta

Risposto
Question about how to run TX and RX calibration example model on zedboard with zynq
Hi Paul, Many thanks for your answer! according to your answer, I should not run tx and rx on one board. However, I cannot u...

circa 6 anni fa | 0

Domanda


Run transmitter and receiver model in 1 model or 2 separate model in parallel
I have only 1 set of the hardware boards(AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard). so I will run both transmitter and re...

circa 6 anni fa | 1 risposta | 0

1

risposta

Risposto
Question about how to run TX and RX calibration example model on zedboard with zynq
In the Matlab help link: https://ww2.mathworks.cn/help/supportpkg/xilinxzynqbasedradio/examples/frequency-offset-calibratio...

circa 6 anni fa | 0

Domanda


Question about how to run TX and RX calibration example model on zedboard with zynq
I am doing an experiment: I combined the following two examples: Transmitter example: https://ww2.mathworks.cn/help/support...

circa 6 anni fa | 3 risposte | 0

3

risposte