Statistica
RANK
16.719
of 292.698
REPUTAZIONE
1
CONTRIBUTI
13 Domande
7 Risposte
ACCETTAZIONE DELLE RISPOSTE
15.38%
VOTI RICEVUTI
1
RANK
of 147.852
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
Domanda
Xpc target data logging at different rate
My xpc model rund at 100Hz. I want to log several data for a week non stop. However, the data doesn't need to be logged every 0....
quasi 12 anni fa | 1 risposta | 0
1
rispostaSystem date and time in XPC target model
Ok found a better working solution here: <http://www.mathworks.nl/support/solutions/en/data/1-1YCWEY/index.html?product=SL&so...
quasi 12 anni fa | 0
| accettato
System date and time in XPC target model
Thanks, but when I try to mex xpcwalltime.c, I receive the following error: Error xpcwalltime.c: 122 type error in argumen...
quasi 12 anni fa | 0
Domanda
System date and time in XPC target model
I need to get the system date and time in my simulink model, which is used for XPC target. In simulink, this is not a problem, u...
quasi 12 anni fa | 2 risposte | 0
2
risposteHow to model discrete sensor simulink
It turned out to be quite simple, using the "Quantizer" block
quasi 12 anni fa | 0
Domanda
How to model discrete sensor simulink
How can I model a discrete sensor in a standard feedback loop model in Simulink? The sensor I try to model gives output at an...
circa 12 anni fa | 1 risposta | 0
1
rispostaDomanda
XPC target serial communication NMEA
I'm trying to read the data send by a NMEA compass on my Xpc target PC. I've read the tutorial from Gordon Weast about this, bu...
circa 12 anni fa | 0 risposte | 0
0
risposteDomanda
Simulink crashes using OPC toolbox
Suddenly I have Simulink crashing when I use the OPC toolbox. When I open the OPC config block to "configure OPC clients", simul...
circa 12 anni fa | 0 risposte | 0
0
risposteDomanda
S-function for reading com-port
I'm trying to read data from a serial port in simulink. The serial configuration blocks and query instrument are not working pro...
oltre 12 anni fa | 4 risposte | 0
4
risposteDomanda
setup OPC server simulink
I try to communicate my simulink model to a PLC (just a few parameters). Therefore, I installed a free OPC server (graybox). ...
oltre 12 anni fa | 0 risposte | 0
0
risposteHow to get system date and time into simulink?
Thanks all, works perfectly now!
oltre 12 anni fa | 0
Domanda
How to get system date and time into simulink?
Is there a way to get the system date and time (not simulation time) into simulink?
oltre 12 anni fa | 5 risposte | 0
5
risposteDomanda
Adding device to Digital Acquisition Toolbox
I try and use the Measurement Computing PMD-1208LS DAQ device with simulink with the Data Acquisition Toolbox. The website te...
oltre 12 anni fa | 0 risposte | 1
0
risposteDomanda
Reading numeric value from COM port
I try to use fscanf( ) to get the numeric heading of an electronic compass. The compass is sending data through COM1 with NMEA s...
quasi 13 anni fa | 1 risposta | 0
1
rispostaDomanda
Serial Receive only zeroes
In simulink, I use the serial receive block to receive data from my NMEA compass, which is sending me heading information throug...
quasi 13 anni fa | 0 risposte | 0
0
risposteDomanda
Reading serial data (NMEA) into simulink
I have a NMEA compass connected to my PC through COM1 (4800 baud, 8 data bits, 1 stop bit, no parity). It sends heading data ...
quasi 13 anni fa | 2 risposte | 0
2
rispostePWM signal Simulink on serial port
Ok right now I have the following code to send to my PSC: ser = serial('COM3') set(ser,'BaudRate',2400, 'Terminator',...
quasi 13 anni fa | 0
PWM signal Simulink on serial port
I found some more info about the brushless motor controller (ESC); The ESC generally accepts a nominal 50 Hz PWM servo input ...
quasi 13 anni fa | 0
PWM signal Simulink on serial port
Ok thanks for all your replies! I want to control a brushless thruster. Because this is a brushless device, it has a special ...
quasi 13 anni fa | 0
Domanda
PWM signal Simulink on serial port
I need to connect my controller designed in Simulink to a brushless motor controller, which needs a PWM signal. This controller ...
quasi 13 anni fa | 5 risposte | 0