photo

Mohamad Nazir


Last seen: circa un mese fa |  Attivo dal 2021

Followers: 0   Following: 0

Statistica

All
  • 3 Month Streak
  • Knowledgeable Level 2
  • Solver
  • First Answer
  • Explorer

Visualizza badge

Feeds

Visto da

Domanda


Connection to target microcontroller error
Hi, I designed an interrupt-based model for object code generation to the target microcontroller including blocks from the targ...

11 mesi fa | 1 risposta | 0

1

risposta

Risposto
Turning voltage on/off in a PV Array and DC motor simulation
What do you mean exactly the controlled voltage source does not work? Did you take into consideration that the load torque will ...

12 mesi fa | 0

Risolto


Calculate BMI
Given a matrix hw (height and weight) with two columns, calculate BMI using these formulas: 1 kilogram = 2.2 pounds 1 inch = 2...

circa un anno fa

Risolto


Plot Damped Sinusoid
Given two vectors |t| and |y|, make a plot containing a blue ( |b| ) dashed ( |--| ) line of |y| versus |t|. Mark the minimum...

circa un anno fa

Risolto


Calculate a Damped Sinusoid
The equation of a damped sinusoid can be written as |y = A.ⅇ^(-λt)*cos(2πft)| where |A|, |λ|, and |f| ...

circa un anno fa

Risolto


Verify Law of Large Numbers
If a large number of fair N-sided dice are rolled, the average of the simulated rolls is likely to be close to the mean of 1,2,....

circa un anno fa

Risposto
how to calculate Zero Sequence inductance(L0)For IPMSM delta connection
The zero sequence inductance can be calculated using L0 = V0open/I​0short​ where V0open​ is the open-circuit voltage for the zer...

circa un anno fa | 0

| accettato

Risposto
How to calculate accurate Sample time for PWM generator block & Current Controller (Here I am using Torque Controller with FOC Controller & 3 Phase IPMSM)
The general rule is Nyquist's theorem which is a sampling frequency at least 10x the frequency of the signal you are trying to s...

circa un anno fa | 0

| accettato

Risposto
in My model I am using torque controller with FOC for IPMSM. How to tune Current Controller PID .Because Current controller have two PID controller.
You can follow the steps of the following example in the link below to tune the current controllers at first and then repeat it ...

oltre un anno fa | 0

Risposto
What is an efficient way to do PID tuning in a model with long computing time?
You can identify a second order transfer function model of your VFD from the open-loop step response (using overshoot, response ...

oltre un anno fa | 1

Risposto
What is the wL block circled in blue called in MATLAB?
Hi, isn't this the velocity multiplied by the inductance? this can be implemented by simply using the product block (https://fr....

oltre un anno fa | 0

Risposto
How can I make a simscape representation of the simulink 'Universal Bridge'
Hi, I think the closest block to the Universal Bridge in the electrical library is https://fr.mathworks.com/help/sps/ref/convert...

oltre un anno fa | 0

Risposto
Transfer function matrix of a Multiple input DC-DC converter
Hi Mohammad, you can probably use Model Linearizer app (https://fr.mathworks.com/help/slcontrol/ug/modellinearizer-app.html) on ...

oltre un anno fa | 0

Risposto
Help required for creating a current sink
Hi, depending on which library you are using, you can use one of the blocks below to model a variable resistor such that the cur...

oltre un anno fa | 0

| accettato

Risposto
Controling multiple switches in a multiple input DC-DC converter
Hi Mohamad, to my understanding you need to have a charging/discharging case which can be simply modelled with a manual switch w...

oltre un anno fa | 0

Risposto
Explaining the function of certain blocks
When a DC motor is supplied with a fixed value DC voltage, it runs at a constant speed (assuming constant load). To control its ...

quasi 2 anni fa | 1

| accettato

Risposto
How to converge 3 phases of simulink voltage onto a simscape VI measurement which accepts 1 port
All you have to do is right click on the current & voltage sensor, choose Simscape > Modeling option > expanded three-phase port...

quasi 2 anni fa | 0

Risposto
Which block to use for BLDC motor for BLDC speed controller design?
BLDC normally denotes a permanent magnet synchronous machine with trapezoidal back-emf waveform. When the machine is called simp...

quasi 2 anni fa | 0

| accettato

Risolto


Solve a System of Linear Equations
Example: If a system of linear equations in x₁ and x₂ is: 2x₁ + x₂ = 2 x₁ - 4 x₂ = 3 Then the coefficient matrix (A) is: 2 ...

quasi 2 anni fa

Risolto


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

quasi 2 anni fa

Risolto


Find the Oldest Person in a Room
Given two input vectors: * |name| - user last names * |age| - corresponding age of the person Return the name of the ol...

quasi 2 anni fa

Risolto


Convert from Fahrenheit to Celsius
Given an input vector |F| containing temperature values in Fahrenheit, return an output vector |C| that contains the values in C...

quasi 2 anni fa

Risolto


Calculate Amount of Cake Frosting
Given two input variables r and h, which stand for the radius and height of a cake, calculate the surface area of the cake you n...

quasi 2 anni fa

Risposto
How can I implement computation step in simulink?
Hi, Depends on what you are trying to achieve. If you want to implement it in Laplace form, for the first block your a is = T...

oltre 3 anni fa | 1

Risposto
Error in PWM Generator Vienna Rectifier
Have you tried to simply insert a "round" block or a "data type conversion" block (or maybe both) for "SmallJexNum" in the "PWM ...

oltre 3 anni fa | 0