Community Profile

photo

Benjamin Thompson


Last seen: 3 giorni fa Attivo dal 2015

Programming Languages:
C++, C, MATLAB
Spoken Languages:
English

Statistiche

  • 12 Month Streak
  • Revival Level 2
  • Knowledgeable Level 4
  • First Answer

Visualizza badge

Content Feed

Visto da

Risposto
fft2 results don't match the analytical Fourier transform results
Your problem is 201 by 201 samples in size? Making the size a power of 2. So use 256.

7 mesi fa | 0

Risposto
Real Time Low Pass Filtering
All digital filters working in real time must have some delay, this is a law of filtering in general. The amount of delay depen...

8 mesi fa | 0

Risposto
Image analysis for speckle pattern
It is possible, try looking over this example: https://www.mathworks.com/help/images/correcting-nonuniform-illumination.html ...

8 mesi fa | 0

Risposto
How to break data in to groups using while loop?
Even better, use the vectorization features in Matlab to count NaNs in each row all at once. nanCounts = sum(isnan(matrix),1); ...

8 mesi fa | 0

Risposto
Replacing specific block with subsystems
Here is one way. I think you would just use a constant block rather than From Workspace because From Workspace is looking to us...

8 mesi fa | 0

| accettato

Risposto
I need to know how to use the for command to calculate y=2/x
x = 1:10; y = 2 ./ x;

10 mesi fa | 0

Risposto
How do I re-use values calculated in a while loop?
Theta1 and Theta2 have not been defined and given a value at the first reference. You should assign an initial value to Theta1 ...

10 mesi fa | 0

Risposto
How do i find the RGB values of color image in range 1 to 255
If the image is stored in MATLAB as a three dimensional array, which is the usual, then the red/green/blue channel is the third ...

10 mesi fa | 0

Risposto
How to create these shapes in Matlab
Where is the m-file referenced in the problem statement? That would probably help on some of the coding structure questions. Y...

10 mesi fa | 1

| accettato

Risposto
Measurement of properties from Tiff image
If you are using the Image Processing Toolbox then you are probably trying to use the regionprops function with the "Area" prope...

10 mesi fa | 0

Risposto
Not able to use the if condition as desired in simulink
You need to use the "if action" subsystem along with the "if". See the example in the documentation: https://www.mathworks.com...

10 mesi fa | 0

| accettato

Risposto
How to copy 30K images from folder to another according to the names in train and test text listes
Use copyfile to copy a file to a new location. You could probably use arrayfun to more quickly add the full file path to the fi...

10 mesi fa | 0

Risposto
Finding average data from a large data matrix
An index vector over the available columns would work well here. Cannot be sure without a complete example of the data. Then p...

10 mesi fa | 0

| accettato

Risposto
Coalesce data from 1000 monte Carlo simulations with different data file lengths?
With the data import tool you can generate a function like this. It needs some editing to handle some of the odd formatting of ...

11 mesi fa | 0

Risposto
Avoid a "loop for" to add multiple "datetime" elements to a cell array
If you can make is an N by 1 cell array and do the assignment using parenthesis indexing and num2cell, then convert that to the ...

11 mesi fa | 0

Risposto
Create Integral, Differential, timer and counter blocks from basic blocks in simulink
You can use a Memory block, subtraction block, and gain block to approximate a differentiator, implementing the equation dx/dt =...

11 mesi fa | 0

Risposto
How to make the flow diagram with if or any hint in Simulink?
A Stateflow chart is usually the best way to model a state diagram in Simulink. Try following the Stateflow Onramp training too...

11 mesi fa | 0

Risposto
How to get the equation of irradiance varying in time for a PV model under partial shading conditions?
Simulink has a 2D lookup table block with various options for interpolation, extrapolation, and fitting. With the two inputs be...

11 mesi fa | 0

Risposto
Hold the value of a signal
You can use the signal builder block to define any type of piecewise continuous signal you want.

11 mesi fa | 0

Risposto
How to pass an input value to a Simulink block from M-file?
Your M file can put the data into the base workspace as a variable with a known name. Then your Simulink model can use the From...

11 mesi fa | 0

| accettato

Risposto
How to change the color of each pixel in a masked image?
See if this helps. There is probably a faster way to do it with color mapping functions in the Image Processing Toolbox but it ...

12 mesi fa | 0

Risposto
I gave the initial condition correctly still the program not working.
circshift returns a vector of the same length as its input. So, j2, j5, j8, and j19 are vectors and not scalar values as the li...

12 mesi fa | 0

Risposto
How can I merge two structs?
Due to the need to merge it might be easiest to use struct2table, table2timetable, make sure it is merged well as a time table, ...

12 mesi fa | 1

Risposto
Displacements and velocity from acceleration integration (accelerometer data)
The Simulink Onramp training course is a good place to start: https://www.mathworks.com/learn/tutorials/simulink-onramp.html?...

12 mesi fa | 0

Risposto
GUI window to manually register two images?
You can try the registrationEstimator app included with the Image Processing Toolbox.

12 mesi fa | 0

Risposto
how to run a simulation at different times
You can use the Signal Builder block to configure how you want a signal to change over time. I assume you are simulating the mo...

12 mesi fa | 0

Risposto
Browsing the subsystem inside model using mscript
You can use open_system to open a Simulink model to some subsystem inside the model. The second parameter to open_system should...

12 mesi fa | 0

| accettato

Risposto
Load array into Simulink model from file without timestamps
If you define your matrix as a Simulink.Parameter in a data dictionary and link to that data dictionary from your model, that wo...

12 mesi fa | 0

Risposto
How can I convert double to const real_T of a sfunction?
If x is a constant you cannot change it. You would need to supply a more complete example, it is hard to tell what you are tryi...

12 mesi fa | 0

Risposto
Simulink code generation for tcpclient
Looks like code generation support for tcpclient was added in R2019B. You may just have a configuration issue in your R2020A te...

12 mesi fa | 0

Carica altro