Todd

John Deere Construction & Forestry

Last seen: 9 giorni fa | Attivo dal 2011

Followers: 0 Following: 0

Messaggio

Statistica

All

Visualizza badge

Feeds

Risolto

Find the Oldest Person in a Room
Given two input vectors: * |name| - user last names * |age| - corresponding age of the person Return the name of the ol...

10 mesi fa

Risolto

Convert from Fahrenheit to Celsius
Given an input vector F containing temperature values in Fahrenheit, return an output vector C that contains the values in Celsi...

10 mesi fa

Risolto

Calculate Amount of Cake Frosting
Given two input variables r and h, which stand for the radius and height of a cake, calculate the surface area of the cake you n...

10 mesi fa

Risolto

Arrange Vector in descending order
If x=[0,3,4,2,1] then y=[4,3,2,1,0]

10 mesi fa

Risposto
How To Reset Dragged Port Order
Putting this here so that it can be marked as the answer: As mentioned by @Andrea Amorosi there is a "reset ports" button on th...

circa un anno fa | 1

Risposto
How can I use sample time internally in Stateflow
Came here to look for a better solution. Here are two imperfect solutions. 1) Use temporal logic, ex. after(5,sec). This make...

oltre un anno fa | 0

Risposto
How to Stop Simulation in Test Sequence Block
One method is to add an output signal that drives a Simulation Stop block.

oltre 4 anni fa | 0

Domanda

Why can't I create a test harness on a subsystem in a reference subsystem?
I can create a Simuilnk Test harness on a subsystem in a model, which is fantastic. However, I cannot create a test harness on a...

oltre 4 anni fa | 1 risposta | 2

1

risposta

Domanda

How do I create a bus object from existing bus element ports
I can use Simulink.Bus.createObject to create a bus object from a bus creator block. How do I create a bus object from a bus def...

oltre 4 anni fa | 1 risposta | 0

1

risposta

Risposto
how to change the display accuracy of cursor data in simulation data inspector
Here's a workaround: Export the plots to a figure, and you can configure data tip format, and do many other things that you can...

quasi 5 anni fa | 0

Risposto
How can I find the top level of the entire system from within an active model reference?
If your reference model is open in a tab of your top model (R2020a+) then you can try this: h = gcbp; sys = bdroot(h.getBlock...

quasi 6 anni fa | 0

Risposto
cross product of by an array
You can represent a cross product as a matrix product a X b = tilde(a)*b where tilde(a) is a skew-symmetric matrix defined by ...

circa 6 anni fa | 0

Risposto
How to implement end position cushioning in a double-acting pneumatic cylinder?
If your cushion works by cutting off air flow out of the cylinder, you can model it as an orifice with an area that changes with...

quasi 7 anni fa | 0

Risposto
Why doesn't my Simscape displacement doesn't match input
One factor is that a step has an infinite derivative, so would be highly sensitive to numerical error. You could try replacing ...

quasi 7 anni fa | 1

Risposto
How to backup my Matlab Favorites
In R2018b it looks like favorites are stored in FavoriteCommands.xml.

quasi 7 anni fa | 4

Risolto

Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

circa 8 anni fa

Risolto

Model a simple pendulum
Model a simple pendulum of length 200cm with bob of mass 100g and plot the position in degrees. The pendulum starts at 30 degree...

circa 8 anni fa

Risolto

Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

circa 8 anni fa

Risolto

Model a mass spring system
Model an ideal mass-spring system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/images/se...

circa 8 anni fa

Risolto

Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

circa 8 anni fa

Risolto

Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

circa 8 anni fa

Risolto

Sort a list of complex numbers based on far they are from the origin.
Given a list of complex numbers z, return a list zSorted such that the numbers that are farthest from the origin (0+0i) appear f...

circa 8 anni fa

Risolto

Create times-tables
At one time or another, we all had to memorize boring times tables. 5 times 5 is 25. 5 times 6 is 30. 12 times 12 is way more th...

circa 8 anni fa

Risolto

Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

circa 8 anni fa

Risolto

Remove any row in which a NaN appears
Given the matrix A, return B in which all the rows that have one or more <http://www.mathworks.com/help/techdoc/ref/nan.html NaN...

oltre 8 anni fa

Risolto

Finding Perfect Squares
Given a vector of numbers, return true if one of the numbers is a square of one of the other numbers. Otherwise return false. E...

oltre 8 anni fa

Risolto

Most nonzero elements in row
Given the matrix a, return the index r of the row with the most nonzero elements. Assume there will always be exactly one row th...

oltre 8 anni fa

Risolto

Fibonacci sequence
Calculate the nth Fibonacci number. Given n, return f where f = fib(n) and f(1) = 1, f(2) = 1, f(3) = 2, ... Examples: Inpu...

quasi 10 anni fa

Risolto

Determine whether a vector is monotonically increasing
Return true if the elements of the input vector increase monotonically (i.e. each element is larger than the previous). Return f...

quasi 10 anni fa

Risolto

Find all elements less than 0 or greater than 10 and replace them with NaN
Given an input vector x, find all elements of x less than 0 or greater than 10 and replace them with NaN. Example: Input ...

quasi 10 anni fa

Carica altro