Todd
John Deere Construction & Forestry
Followers: 0 Following: 0
Statistica
RANK
3.359
of 301.529
REPUTAZIONE
17
CONTRIBUTI
5 Domande
10 Risposte
ACCETTAZIONE DELLE RISPOSTE
40.0%
VOTI RICEVUTI
9
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
How To Reset Dragged Port Order
Putting this here so that it can be marked as the answer: As mentioned by @Andrea Amorosi there is a "reset ports" button on th...
12 mesi fa | 1
How can I use sample time internally in Stateflow
Came here to look for a better solution. Here are two imperfect solutions. 1) Use temporal logic, ex. after(5,sec). This make...
oltre un anno fa | 0
How to Stop Simulation in Test Sequence Block
One method is to add an output signal that drives a Simulation Stop block.
circa 4 anni fa | 0
Domanda
Why can't I create a test harness on a subsystem in a reference subsystem?
I can create a Simuilnk Test harness on a subsystem in a model, which is fantastic. However, I cannot create a test harness on a...
oltre 4 anni fa | 1 risposta | 2
1
rispostaDomanda
How do I create a bus object from existing bus element ports
I can use Simulink.Bus.createObject to create a bus object from a bus creator block. How do I create a bus object from a bus def...
oltre 4 anni fa | 1 risposta | 0
1
rispostahow to change the display accuracy of cursor data in simulation data inspector
Here's a workaround: Export the plots to a figure, and you can configure data tip format, and do many other things that you can...
quasi 5 anni fa | 0
How can I find the top level of the entire system from within an active model reference?
If your reference model is open in a tab of your top model (R2020a+) then you can try this: h = gcbp; sys = bdroot(h.getBlock...
oltre 5 anni fa | 0
cross product of by an array
You can represent a cross product as a matrix product a X b = tilde(a)*b where tilde(a) is a skew-symmetric matrix defined by ...
quasi 6 anni fa | 0
How to implement end position cushioning in a double-acting pneumatic cylinder?
If your cushion works by cutting off air flow out of the cylinder, you can model it as an orifice with an area that changes with...
oltre 6 anni fa | 0
Why doesn't my Simscape displacement doesn't match input
One factor is that a step has an infinite derivative, so would be highly sensitive to numerical error. You could try replacing ...
oltre 6 anni fa | 1
How to backup my Matlab Favorites
In R2018b it looks like favorites are stored in FavoriteCommands.xml.
oltre 6 anni fa | 4
emlc generates two different c-files for the same supporting function when building two functions, how do you merge them?
I suppose I could build a library (.lib) for each function. Then I would have redundant object code, but at least I would have ...
oltre 14 anni fa | 0
Domanda
emlc generates two different c-files for the same supporting function when building two functions, how do you merge them?
If I have two functions: function y = fcn1 %#eml A = [ 8 1 3 5 4 9 ]; y = pin...
oltre 14 anni fa | 2 risposte | 0
2
risposteDomanda
Specifying function names in generated code using emlc
How do I specify what name emlc will assign to a function that it generates? I'm looking for something like the eml.cstructname...
oltre 14 anni fa | 1 risposta | 0
1
rispostaDomanda
Specifying inputs/outputs for C-code functions generated from MATLAB m-code using emlc as pass-by-reference
How do I make the generated c-code use pass-by-reference for all inputs and outputs instead of pass-by-value? I am using emlc...
oltre 14 anni fa | 1 risposta | 1
