Community Profile

# Venkatesh Chilapur

Last seen: 3 giorni fa Attivo dal 2017

All

#### Content Feed

Visto da

Inviato

DC-DC Buck Converter Simulink Model using STM32 BG474EDPOW1
This submission contains an example model that implements a DC-DC Buck Converter using STM32 BG474EDPOW1 Discovery Kit.

Inviato

Simulink Reference Application Examples for TI C2000
This repository will host Simulink reference application examples using Embedded Coder TI C2000 Support Package.

Risolto

Whether the input is vector?
Given the input x, return 1 if x is vector or else 0.

8 mesi fa

Risolto

Flip the vector from right to left
Flip the vector from right to left. Examples x=[1:5], then y=[5 4 3 2 1] x=[1 4 6], then y=[6 4 1]; Request not ...

8 mesi fa

Risolto

Arrange Vector in descending order
If x=[0,3,4,2,1] then y=[4,3,2,1,0]

8 mesi fa

Risolto

Find the sum of all the numbers of the input vector
Find the sum of all the numbers of the input vector x. Examples: Input x = [1 2 3 5] Output y is 11 Input x ...

8 mesi fa

Risolto

Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

8 mesi fa

Risposto
Hi Federico, See if this helps! problem with F28379D - MATLAB Answers - MATLAB Central (mathworks.com) Regards, Venkatesh C

circa un anno fa | 0

Risposto
Problems with data visualization in parameter tuning with serial communication and buffered data (Ti C2000)
Hi Dominik, See if you can use the two model approach. How can I use a two model approach for signal logging and parameter tun...

circa un anno fa | 0

| accettato

Risposto
Failed to build model for TI-C2000 with Simulink
Hi Wei, Make sure if you have followed all the steps related to 'setup' of the supportpackage. More details can be found here: ...

circa un anno fa | 0

Risposto
is simulink support for Aurix TC297 microcontroller for Model Based Design
Hi Manohar, There can be following approaches (Option 2 or 3 in your case): The board or the MCU is already supported by MATLA...

circa un anno fa | 0

Risposto
I2C Transmit com => Launchpad F28379D freeze

circa un anno fa | 0

Risposto
Generate C code for MC33771 and S32K for SOC/SOH standlone oepartion
Hi Balwinder, There can be following approaches (Option 2 or 3 in your case): The board or the MCU is already supported by MAT...

circa un anno fa | 1

Risposto
Creating bit stream for SPI devices
Hi, Please refer the shipping example - c28x_spi_eeprom/Write EEPROM Data which will provide a very good overview on how you ca...

circa un anno fa | 1

Risposto
STM32F767ZI Simulink - "The target configuration uses time from a local timer, which is not based on simulation time"
Hi, This is a known limitation. If you use HW timer for getting the timestamps, you can't use Scope/Display to visualize signal...

circa un anno fa | 0

Risposto
How to give control command through MATAB to Code Composer Studio code
Please refer the following example which showcases the 2 model approach. Here you can command a control value from Host model to...

circa un anno fa | 0

Risposto
Texas Instruments C2000 PMSM Control
Please find the following details on TIC2000 SPKG reference material: (Under section 3 below, one can find Motor control example...

circa un anno fa | 0

Risposto
Overcurrent protection using One shot trip TI 28379D

circa un anno fa | 0

Risposto
Trip-zone using Embedded Coder Support Package for Texas Instruments
Hi Krishnan, You may also want to do the following settings: Upon the trip condition the above setting will esure the outp...

circa un anno fa | 0

Risposto
CLA Compiler Errors Using Embedded Coder for Texas Instruments C2000 Processors
Hi Grant, We used your model and made couple of changes. Change from Switch to If-else Unit delay and Memory block at: gatedr...

oltre un anno fa | 0

Risposto
TMS320F28379D: Use DMA in CLA to Assign Counter Compare Values (Simulink Coder)
It is either DMA or CLA that can access the peripheral registers at a given time. We choose between either DMA or CLA to access...

oltre un anno fa | 0

| accettato

Risposto
Trip-zone using Embedded Coder Support Package for Texas Instruments
Hi Mohammed, On the ePWM block Mask you will find the Tab for Trip Zone configuration. Here you can enable CBC and OST trips he...

circa 2 anni fa | 0

Risposto
C2000 series FFT analysis problem
Hi, Please check out this example and let me know if you have more questions. https://www.mathworks.com/help/supportpkg/texasi...

circa 2 anni fa | 0

Risposto
PWM-triggered CLA in Embedded Coder
Hi, Please try attached model. You can get more details on the configurations around RT block from the model 'c28379D_datainte...

circa 2 anni fa | 0

Risposto
PWM-triggered CLA in Embedded Coder
Hi, It is likely that the Class of the simulink parameter Cla_out might not be updated. It can be updated by following the bel...

circa 2 anni fa | 0

Risposto
Code Replacement Library for TI C2000 Microcontrollers

circa 2 anni fa | 0

Risposto
program will not fit into available memory ".cinit"

circa 2 anni fa | 0

| accettato

Risposto
check connection between Dsp Ti c2000 board with matlab
Hi, There is a getting started video for Embedded Coder Support Package for Texas Instruments C2000 Processors which can help...

circa 2 anni fa | 0

Risposto
Computational strength between C2000 CLA and CPU
Hi, As we know CLA is a 32-bit floating point math accelerator. So any part of the algorithm that involves Math based computati...

circa 2 anni fa | 0

Risposto
About EPWM BLOCK - TI C2000 DC/DC Buck Converter Example
Hi, The first factor i.e 15 is related to the ADC SOCx acquisition window. The second factor i.e 54 is time from the end of the...

circa 2 anni fa | 1