Manikandan
anna university
Followers: 0 Following: 0
Statistica
RANK
2.811
of 300.331
REPUTAZIONE
22
CONTRIBUTI
4 Domande
46 Risposte
ACCETTAZIONE DELLE RISPOSTE
0.0%
VOTI RICEVUTI
8
RANK
3.572 of 20.920
REPUTAZIONE
430
VALUTAZIONE MEDIA
4.80
CONTRIBUTI
3 File
DOWNLOAD
7
ALL TIME DOWNLOAD
4111
RANK
of 168.124
CONTRIBUTI
0 Problemi
0 Soluzioni
PUNTEGGIO
0
NUMERO DI BADGE
0
CONTRIBUTI
0 Post
CONTRIBUTI
0 Pubblico Canali
VALUTAZIONE MEDIA
CONTRIBUTI
0 Punti principali
NUMERO MEDIO DI LIKE
Feeds
PI control techniques for speed control of a BLDC motor
Try to use trial and error method
oltre 7 anni fa | 0
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...
oltre 9 anni fa | 3
Inviato
Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in
oltre 9 anni fa | 2 download |
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...
oltre 9 anni fa | 0
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.
oltre 9 anni fa | 0
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in
oltre 9 anni fa | 0
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...
oltre 9 anni fa | 0
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...
oltre 9 anni fa | 0
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.
oltre 9 anni fa | 0
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in
quasi 10 anni fa | 1
how to find the setpoint ref input block in simlink for design of PI controller to control speed of servo motor... i can't find the setpoint bock in simulink.... setpoint ref input block...
use constant block
quasi 10 anni fa | 2
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in
quasi 10 anni fa | 1
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in
quasi 10 anni fa | 0
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]
quasi 10 anni fa | 0
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.
quasi 10 anni fa | 0
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.
quasi 10 anni fa | 0
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf
quasi 10 anni fa | 0
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.
quasi 10 anni fa | 0
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.
quasi 10 anni fa | 1
there is a built in model of brushless DC motor in simulink library. does anyone know the equations used for built in model of BLDC.
like it.
quasi 10 anni fa | 0
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...
quasi 10 anni fa | 0
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.
quasi 10 anni fa | 0
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in
quasi 10 anni fa | 0
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....
quasi 10 anni fa | 0
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...
quasi 10 anni fa | 0
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...
quasi 10 anni fa | 0
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...
circa 10 anni fa | 0
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in
circa 10 anni fa | 0
