Dimitri MANKOV

Last seen: 3 giorni fa | Attivo dal 2020

Followers: 1 Following: 0

Statistica

All

Feeds

Risposto
How to send n number of messages through standard can pack unpack and speedgoat IO blocks
Hi Akhila, Could you please provide more details about that you mean by "I am changing in SLRT explorer but signal is not recei...

19 giorni fa | 1

| accettato

Risposto
use xpcbench to bench a user model using simulink real-time 2015b
Hi Howard, That's a tough question to answer, especially for such an old MATLAB release... But perhaps you could use an alterna...

circa 2 mesi fa | 0

Risposto
MCC PCI-DAS on 64-bit Matlab Simulink real-time
Hi Janez, I'm afraid that's rather unlikely because of the efforts that would be required to adapt the driver blocks. Please al...

3 mesi fa | 0

Risolto

Verify Law of Large Numbers
If a large number of fair N-sided dice are rolled, the average of the simulated rolls is likely to be close to the mean of 1,2,....

3 mesi fa

Risolto

Solve a System of Linear Equations
Example: If a system of linear equations in x₁ and x₂ is: 2x₁ + x₂ = 2 x₁ - 4 x₂ = 3 Then the coefficient matrix (A) is: 2 ...

3 mesi fa

Risposto
Relax real time requirement on Speedgoat on startup
Hello Thomas, Absolutely, this is possible using the SLRT Overload Options block, either via the "Startup duration" setting (if...

3 mesi fa | 0

| accettato

Risposto
Get the xPC Target (Simulink Real-time) message log to the host computer
Hi Thomas, In MATLAB R2020a and earlier, you can use the following command to retrieve the entire target console log: Simulink...

4 mesi fa | 0

Risposto
xPC Target Logging in folders
Hi Carl-Johan, This used to be rather complicated to achieve in MATLAB R2020a and earlier, but is very straightforward in Simul...

5 mesi fa | 0

Risposto
Unable to run rtwmakecfg file. Insufficient number of outputs
Hi Donovan, In the vast majority of cases related specifically to Simulink Real-Time in R2020a and earlier, this (admittedly cr...

5 mesi fa | 0

Risposto
How can I run 'slrttest' on my PC?
Hi Chuanxin, Could you please have a look at the following MATLAB Post? The issue diescription is very similar, and could be du...

7 mesi fa | 0

Risposto
Can Simulink Real-time Send and Receive Data to a Host over Ethernet without involving MATLAB?
Hi Jari, Thanks for asking! The Simulink Real-Time target machine can communicate via UDP or TCP/IP with any external device su...

8 mesi fa | 0

| accettato

Risposto
Real Time Robotic Arm
Hello Ceren, One possible approach would be to look into the Simulink Real-Time toolbox, which would allow you to deploy your S...

9 mesi fa | 0

Risposto
Simulink Real Time External Mode Requirements
Hi Diede, For the Host PC, the system requirements can be found for every MATLAB release here. Note that these are minimal requ...

10 mesi fa | 0

Risposto
Hold signal value in after a trigger then resume with the rest of the signal
Hi Yan, What about a triggered subsystem containing your counter, like in the picture below? That counter would only be increme...

11 mesi fa | 0

Risposto
Error message when running simulink real-time with Speedgoat
Hi Jeseong, Looks like your target machine crashed. Not sure if this will work on a release as old as R2015b, but in R2020a and...

11 mesi fa | 0

Risposto
Simulink Real-Time UDP block vs Instrumentation Toolbox UDP block
Hi Cheng, It depends: do you intend to run your Simulink model on an external target machine, or on your development PC? If you...

12 mesi fa | 0

| accettato

Risposto
issues about RateTransition block when performed serial communiction on Speedgoat
Hi Yunchao, Could you open the Diagnostic Viewer on the bottom of your Simulink model, and select the correct log (Build) as sh...

12 mesi fa | 1

Risposto
XPC trigger model run
Hi Istvan, In MATLAB R2020a or earlier, you can use the "IRQ Source" block to trigger a subsystem of your Simulink model asynch...

circa un anno fa | 0

| accettato

Risposto
Can't send multiple CAN FD messages with 1 send block on Speedgoat
Hi Szilard, Could you try using a "Vector Concatenate" block instead of a "Mux" block to pass several CAN-FD messages to the "C...

circa un anno fa | 0

| accettato

Risposto
Using Simulink RT on development laptop to communicate with Beckhoff EK1100 module
Hi Thomas, I'm afraid the EtherCAT blocks from the Simulink Real-Time library will not work on your desktop computer: Simulink ...

circa un anno fa | 0

| accettato

Risposto
how to learn Hardware-in-loop testing ?
Hi, The MathWorks offer a great course about Simulink Real-Time that covers the topic of HIL testing, check it out here: https...

circa un anno fa | 0

| accettato

Risposto
Signals with Fixed-Point data types in Simulink Real-Time
Hi Francesca, Which MATLAB release are you using? The documentation you are referencing applies to R2023b, but I see that you e...

circa un anno fa | 0

Risposto
time-triggered CAN simulation
Hi Ruoshi, There are several approaches to real-time simulation, including Simulink Real-Time and Simulink Desktop Real-Time. W...

oltre un anno fa | 0

Risposto
Serial and Ethernet connection for xpc target
Hi Le, I'f you'd like to send data over the serial / COM port of your target machine, you can use the RS-232 blocks from the xP...

oltre un anno fa | 0

Risposto
How to change block sample time using a trigger
Hi Thomas, I would simply move the TCP Send block inside of the triggered / enabled subsystem, this should do the trick :) Bes...

oltre un anno fa | 0

| accettato

Risposto
Speedgoat Hardware for noise control
Hi Russ, The hardware used in this example is a Speedgoat Performance tagret machine with an IO104 module. Speedgoat offers a w...

oltre un anno fa | 0

| accettato

Risposto
TCP/IP Connection xPC Target with remote device
Hi Tobias, You can use the TCP/IP driver blocks from the Simulink Real-Time library in the model that you deploy to your target...

oltre un anno fa | 0

Risolto

De-dupe
Remove all the redundant elements in a vector, but keep the first occurrence of each value in its original location. So if a =...

oltre un anno fa

Risolto

intersection of matrices
Given two matrices filled with ones and zeros, determine if they share a common row, column entry. These matrices are of identic...

oltre un anno fa

Risolto

First non-zero element in each column
For a given matrix, calculate the index of the first non-zero element in each column. Assuming a column with all elements zero i...

oltre un anno fa

Carica altro

Dimitri MANKOV

Statistica

MATLAB Answers

Cody

Cody

Cody

Cody

Cody

MATLAB Answers

File Exchange

MATLAB Answers

Community

Cody

MATLAB Answers

Feeds