Statistics
RANK
330
of 257.947
REPUTATION
210
CONTRIBUTIONS
0 Questions
113 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
13
RANK
1.571 of 17.774
REPUTATION
1.089
AVERAGE RATING
4.40
CONTRIBUTIONS
6 Files
DOWNLOADS
247
ALL TIME DOWNLOADS
8553
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Content Feed
Submitted
E-mobility - Regenerative Braking - Off-shore Micro-grid
Simulation kit to study resilience and energy management in electrical grids, perform regenerative braking and manage faults ef...
5 mesi ago | 36 downloads |

Submitted
Electric Vehicle Rolling over Off-Road Uneven Terrain
Contact modeling with Spatial Force Blocks, Point Cloud and Grid Surface. Electric Propulsion. Analysis & visualization of vehic...
6 mesi ago | 10 downloads |

Submitted
Green Hydrogen from Water Electrolysis.
Simscape implementation of a conceptual electrolyzer converting electricity and water into hydrogen gas.
6 mesi ago | 96 downloads |

Submitted
Fuel Cell-Battery Driven Electric Motor & Hydrogen Transfer
Electric Motor fed by Fuel Cell-Battery. Calibration based on I-V Datasheet Curve. Thermodynamic Analysis of Hydrogen Transport....
6 mesi ago | 54 downloads |

How to input [Po Qo] and [np np] as a timeseries to a Three-Phase Dynamic Load block?
Hi there You have two ways of using the PQ block. In the first case, the dynamic profile of the load is determined by the initi...
11 mesi ago | 0
PV array with grid system with battery charger
Hi there The synchronization is done through a PLL block that senses the voltage of the grid and obtains the phase angle to be ...
11 mesi ago | 0
Replace a generic engine with a synchronous machine
Hello Sebastian Based on your description, I believe that the Motor & Drive System Level block (see link below) comes closest t...
11 mesi ago | 1
| accepted
Control of Vienna rectifier
Hi there Please check this demo https://se.mathworks.com/help/physmod/sps/ug/vienna_rectifier.html Using the Simscape Elec...
11 mesi ago | 0
Simcape simulation won't start due to "Model not assembled: position violation" error, how do I fix it?
Hi Lovre This is an indication that the kinematics in your mechanism are not physically possible. If the model is not too compl...
11 mesi ago | 0
Simscape Multibody: Zero crossing in control loop
Hi Irina It looks like you are allocating the angles in a closed loop (sign dependent) and then forcing a kinematic behaviour...
12 mesi ago | 1
| accepted
How do I attach blocks from the foundational library of simulink to the multibody blocks of simulink?
Hi Roberto Please check out the link below to solve the issue you named. https://se.mathworks.com/help/physmod/simscape/re...
12 mesi ago | 0
| accepted
fft analysis tool in powergui doesn't work
Hi there you need to open the FFT tool in a model with an electric model where you have previously saved current or voltage i...
12 mesi ago | 0
Two-Phase Fluid Properties (2P) for Helium
Hello Saara Unfortunately not. The way to do it would be through the two phase fluid settings block (Simscape Foundation Libr...
12 mesi ago | 0
| accepted
Simscape Multibody Contact Forces Mecanum Wheels
Hi there When look at the wheels, it looks like they are made of transversal cylinders on the perimeter. Rolling would be dis...
12 mesi ago | 1
| accepted
How to create contact between wheel and floor while making the wheel roll on the floor ?
Hi there Definitely, using the spatial force contact block would be the best option. See the submission below with an impleme...
12 mesi ago | 0
| accepted
how to make the small ball slide into the groove in simscape
Hello there I gave the mechanism a good try. It is all about positioning components with precision and then use the spatial for...
circa un anno ago | 1
| accepted
How can I plug inverse kinematics to a Simscape multibody?
Hello there You need to set the joint in kinematic mode (Actuation >> Motion - Prescribed / Torque - automatically calculated...
circa un anno ago | 0
Adding contact blocks to a model imported from Inventer into Simscape
Hi there You need a spatial force contact block taking in both geometries to resolve the contact. Modeling Contact Force Betwee...
circa un anno ago | 0
| accepted
Submitted
Soft Starter Induction Motor Model
Electro-mechanical model of a thyristor-based soft starter with Simscape Electrical
circa un anno ago | 33 downloads |
Fuel Cell to Battery
Hello Mateo Many years have gone but this type of system is more actual than ever. Please see the link below: https://www....
circa un anno ago | 0
Using fuel cell stack and battery with electrical domain
Hi Hugo, An alternative you can think of is to do everything in Simscape. The link below may be helpful. This complements Jav...
circa un anno ago | 0
how to make a hydrogen fuel cell and battery hybrid to power a motor simulink
Hello Serge, You will find the link below interesting to tackle your question. https://www.mathworks.com/matlabcentral/fil...
circa un anno ago | 0
import multiple step files into simscape
Hi there Kim You shall export the geometry in the File Solid blocks and then use Spatial Force Contact blocks between solids....
circa un anno ago | 1
| accepted
how to determine base equation of heat flow rate sensor to calculate the heat generated by battery pack in simscape fluids
Hi there Please check out this submission. It captures cooling of Battery packs really well. https://www.mathworks.com/mat...
circa un anno ago | 0
Simscape Driveline Ideal Motion Sensor - Calculating Acceleration
Hi Peter This is good feedback, maybe there should that option in the sensor. But this can be solved by adding that into a mo...
circa un anno ago | 0
Moist Air Modeling error: Solver was unable to reduce the step size
Hello Guangwei I think the model may have some issues. It looks like you are filling/emptying the chamber. This leads in the ...
circa un anno ago | 0
| accepted
How to add or fix a spring in simscape Multibody?
Hi there Please check the link Interface between mechanical translational networks and Simscape Multibody joints - MATLAB (math...
circa un anno ago | 0
| accepted
Kinematic Analysis of 5dof Manipulaor Arm Simscape MultiBody
Hi Joe, Cool to see that you use Simscape Multibody. You need to set the joints in kinematic mode to accomodate the prescribed ...
circa un anno ago | 0
| accepted
Contact Modelling: Possible to model a vehicle driving over an 'obstacle course'?
Hello Rory I'd like to give this question a shot. The contact between the tires and uneven terrain can be modelled in the lates...
circa un anno ago | 0
Could two rotational mechanical signals be added up/summed directly?
Hi Xu Based on your short description I would do as in the image below. This is often common for BEV models. The differential g...
circa un anno ago | 0